ADB Signature Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 51

background image

L-852C-D ITCL Taxiway Centerline Inset Lights

Troubleshooting

©

2007 Siemens Airfield Solutions

96A0311F

Page 5-2

All rights reserved

Issued 3/05

Troubleshooting procedures for the F-Range inset lights are contained here.

NOTE:

The cordset should never be replaced because of problems disconnecting

the cordset from the PCB. If the cordset needs to be replaced, then the entire inner
cover assembly must be replaced.

Problem Possible

Cause

Corrective

Action

1. LED not energizing

LEDs defective

Replace LED assembly. Refer to

Replacing

LED Assembly

in the

Repair

section.

PCB defective

Replace the complete inner cover.

Moisture inside assembly causing
current leakage

Open up light assembly. Clean, dry, and inspect
light assembly. Replace O-ring.

No connection of primary loop.
Defective isolation transformer or
secondary wiring

Check transformer output current with true
RMS ammeter.

Check power line between the light fixture and
the transformer, including connectors.

2. Weak light output

Partial short circuit in primary loop

Check cable assembly.

Defective isolation transformer

Replace transformer.

Dirty prism

Incorrect current to fixture

Clean prism. Refer

to Cleaning Light Channel

and Prism

in the

Maintenance

section.

Check the current to the fixture to ensure it is
within FAA specifications for the selected step.
If not, adjust the CCR or repair circuit issues.
Ensure that the isolation transformers have
adequate capacity to run the fixture, especially
if using arctic kit.

3. Light beam distorted

Broken or damaged prism/cover

Replace prism or entire fixture. Refer to

Replacing Prism and Prism Gasket

in the

Repair

section.

4. Short LED life

Current too high

Check output current of isolating transformer at
full brightness. Current should not exceed 6.7
A.

Replace transformer if defective; if not, adjust
CCR output current.

2.

Troubleshooting

Procedures

«
...
28
29
30
31
32
...
»

Содержание Signature Series




















































Отзывы:

Нет отзывов

Похожие инструкции для Signature Series

Бренд: Radio Shack Страницы: 52

Бренд: Canon Страницы: 2

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

Бренд: Uclear Страницы: 40

Бренд: Quectel Страницы: 90

Бренд: Talgil Страницы: 14

Бренд: Tadao Страницы: 2

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

FX-COMM4NDER MFX3203

Бренд: Magicfx Страницы: 16

Бренд: Altronix Страницы: 8

Бренд: nvent Страницы: 6

Бренд: Smart Vision Страницы: 5

Бренд: Teledyne Страницы: 47

Бренд: Western Co Страницы: 14

Бренд: BabyActive Страницы: 4

Бренд: HomeMatic Страницы: 36

Бренд: Kohler Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды