ADB Signature Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 51

background image

L-852C-D ITCL Taxiway Centerline Inset Lights

Safety

©

2009 ADB Airfield Solutions, LLC.

96A0311F

Page 1-5

All rights reserved

Issued 3/05

•

Do not service or adjust any equipment unless another person trained in first
aid and CPR is present.

•

Connect all disconnected equipment ground cables and wires after servicing
equipment. Ground all conductive equipment.

•

Use only approved ADB Airfield Solutions replacement parts. Using
unapproved parts or making unapproved modifications to equipment may
void agency approvals and create safety hazards.

•

Check interlock systems periodically to ensure their effectiveness.

•

Do not attempt to service electrical equipment if standing water is present.
Use caution when servicing electrical equipment in a high-humidity
environment.

•

Use tools with insulated handles when working with electrical equipment.

«
...
10
11
12
13
14
...
»

Содержание Signature Series




















































Отзывы:

Нет отзывов

Похожие инструкции для Signature Series

Бренд: Falcon Страницы: 3

Бренд: OBaby Страницы: 47

Бренд: FAAC Страницы: 12

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

REVOLUTION Pro Controller 2

Бренд: Nacon Страницы: 11

Бренд: Nacon Страницы: 18

Бренд: Nacon Страницы: 24

Бренд: Nabco Страницы: 35

Бренд: UNICORECOMM Страницы: 32

Бренд: UNICORECOMM Страницы: 7

Бренд: UNICORECOMM Страницы: 26

Бренд: UNICORECOMM Страницы: 25

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Simply Smart PY75 A Series

Бренд: BABYTREND Страницы: 32

Бренд: Yolink Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды