manualshive.com logo in svg

ADB MIKADO, Руководство пользователя

Поделиться
Скачать
ADB MIKADO Скачать руководство пользователя страница 21

MIKADO USER MANUAL 

 

 

 

 

 

www.adblighting.com

 

User Manual - page 19 
Issue 1.0 
 

To record a Memory as a step, select the required page by tapping [PAGE] (optional) then 
tap [F/A] (Memory number). You cannot record a Chaser as a step in a Chaser. 
 
To record a snapshot of the output as a step, create the desired look on the output, then 
press [record memory]. 
 
Continue to record steps as above. 
 
When all steps have been recorded, press [record chaser] to end. 
 

6.2.1  RECORDING THE SPEED (RATE) 

If a Chaser is recorded with the SPEED rotary fader set to zero, no speed will be stored with 
the Chaser. When the Chaser is played back the SPEED rotary fader can be used to vary 
the speed manually. 
 
If a Chaser is recorded with the SPEED rotary fader set above zero, the speed setting will be 
stored with the Chaser. 
 
To add a speed to the recorded Chaser, adjust the [speed] rotary fader clockwise/counter 
clockwise until the LED lights or starts flashing (this indicates the previous submaster speed) 
then set the rate using the flashing LED to gauge the speed. 
 
The speed can be varied after recording by editing the Chaser (see below). 
 

6.2.2  RECORDING THE CROSSFADE TIME 

If a Chaser is recorded with the CROSSFADE rotary fader set to zero, no crossfade setting 
will be stored with the Chaser. When the Chaser is played back the CROSSFADE rotary 
fader can be used to vary the crossfade between steps manually. 
 
If a Chaser is recorded with the CROSSFADE rotary fader set above zero, the crossfade 
setting will be stored with the Chaser. 
 
To add a crossfade to the recorded Chaser, adjust the [crossfade] rotary fader 
clockwise/counter clockwise until the LED lights (this indicates the previous submaster 
crossfade setting) then adjust the rate using scale printed around the rotary fader. 
 
The crossfade can be varied after recording by editing the Chaser. 
 

Содержание MIKADO





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды