ADB Safegate UEL-1-120 Скачать руководство пользователя страница 19

Страница: 19 / 42

4.5.2 Procedure

1. UEL-1-150 steady burning light

The following table instructs you on how to install the UEL-1-150 on a 60 mm O.D. conduit:

a) Before installing the light, prepare a two-core cable with plug, making sure that a sufficient length of cable is available

above the conduit elbow or cover plate. Connect the plug of the two-core cable to the receptacle of the cable coming

from the transformer.

Note

The transformer receptacle rests in the upper part of the conduit elbow or the cover plate.

CAUTION

Do not tape the plug/receptacle assembly in order to allow for quick disconnection in case of impact.

b) Install the breakable coupling on the conduit elbow or cover plate, and the conduit on the breakable coupling.

CAUTION

Make sure that the conduit is perfectly vertical, using the screws of the breakable coupling for adjustment.

Tighten the counter-nuts.

c) Remove the optical cartridge (1) by hinging it down and lifting it out of the hinge.

Insert the two-core cable through the housing (3), and install the light without optical cartridge on the conduit,

without tightening the bracing clamp (5).

d) Clamp the cable into the stress reliever (6).

Note

In case of a top light, the two cables should be clamped into the cable stress reliever.

e) Cut the two-core cable in the light fitting to the right length, maintaining sufficient slack to easily connect it to the

lamp with the cartridge hinged down.
Crimp the "fast-on" connectors on the cores of the cable.
Slip the insulation sleeves over the cores of the cable.

f) Adjust the position of the light unit, see §

Orientation and elevation settings

g) Once the position of the light is correct, put the optical cartridge back in place.
h) Connect the lamp to the fast-on connectors.

CAUTION

To avoid short-circuits, make sure to slip the insulation sleeves over the fast-on connectors.

i) Close the light fitting.

2. UEL-1-120 flashing light

The following table instructs you on how to install the UEL-1-120 on a 60 mm O.D. conduit:

a) Before installing the light, make sure that a sufficient length of 5-core cable coming from the FCU cabinet is available

above the conduit elbow.

b) Install the breakable coupling on the conduit elbow or cover plate, and the conduit on the breakable coupling.

WARNING

The conduit must be perfectly vertical, using the screws of the breakable coupling for adjustment. Tighten the

counter-nuts.

UM-4020 / AM02-630e, Rev. 2.0, 2020/05/19

Содержание UEL-1-120










































Результаты поиска

Содержание UEL-1-120

Отзывы:

Похожие инструкции для UEL-1-120

Бренды по названию

Популярные бренды

ADB Safegate UEL-1-120, Руководство пользователя

Результаты поиска

Содержание UEL-1-120

Отзывы:

Похожие инструкции для UEL-1-120

Бренды по названию

Популярные бренды