Adaptive AlphaXpress 8731 Скачать руководство пользователя страница 31

Страница: 31 / 56

QUIPMENT

NSIDE

VIEW

AlphaXpress 8731 Sign Installation and Maintenance Manual (pn 1508610601 rev. A)

LED driver board

The size of the sign determines the number of driver boards in the sign (for example, a 27 x 54 sign would
have 27 driver boards; a 27 x 72 sign would have 36). Each board is 6 x 9 pixels, and each pixel is composed
of 8 LED lamps.

Figure 26.

LED driver board, front and back views.

Item

PCB label

Name

Description

LD1

POWER

On = 12V supplied to LED driver board.

LD2

FAULT

On = one or more bad LED lamps on the LED driver board (if in normal operating mode).

LD3

COMM

On = There is NO communication from sign controller.
Off = There is communication from the sign controller.

LD4

RUN

Flashing = LED driver board processor operating.

BIN LABEL

Information on the intensity and wavelength of the LED lamps.

DATA

Connects to Controller #1 via a ribbon cable.

Programming port for the LED driver board processor.

LED DRIVER BOARD
ADDRESS

This address is set using an address plug (pn 1509100701).

+V1

Supplies power to the LED driver board.

Front view

6 pixels

Back view

9 pixels

Jumper wires

Refer to the appropriate wiring

diagram for your sign model. These

are preset from the factory with the

correct settings.

Plugs into P2

Содержание AlphaXpress 8731

























































Результаты поиска

Содержание AlphaXpress 8731

Отзывы:

Похожие инструкции для AlphaXpress 8731

Бренды по названию

Популярные бренды

Adaptive AlphaXpress 8731, Руководство по установке и обслуживанию

Результаты поиска

Содержание AlphaXpress 8731

Отзывы:

Похожие инструкции для AlphaXpress 8731

Бренды по названию

Популярные бренды