2010 ATM Fly-Ware, Signal Hill, CA 90755 (562) 424-1100
Rev. 00 -050510
Figure 2
Figure 3
Step 3:
Carefully flip the two speakers together so that the top is facing up.
Removed the screws in the holes where the joiner plates are installed.
Install the joiner plates using the same holes as the bottom joiner plates
using the provided screw, split washer and flat washer (Figure 3).
Step 4:
Install the M10 x 35mm long eyebolts with flat washers on the outer front
holes of the side speaker (Figure 3).
Step 5:
Install the M10 x 35mm long eyebolt on the top rear of the speaker then
bridle to a single pull back cable (Figure 3). For dual pullback point
attach a pullback cable on each rear eyebolts.
Step 6:
When all joiner plates are installed, tighten screws permanently.
Step 7:
Attach a load rated suspension cables or chains on the top front
eyebolts. Use the rear eyebolts for pull back points and to adjust the tilt
angle of the loudspeaker cluster assembly as shown in the main
illustration (Figure 4).
Step 8:
Check all hardware connections before hoisting cluster.
Figure 4
Installation Guide
FP-EVH1152-2X1
ELECTRO-VOICE CLUSTER PACK PLANAR ARRAY KIT
The FP-EVH1152-2X1 planar array kit gives designers, contractors and audio
consultants the ability to create two EVH 1152 speakers in a tight pack or splayed
configurations. The FP-EVH1152-2x1 kit provides a method of flying a planar or
line array configuration while offering the capability of allowing cabinet’s splay angle
to be adjusted relative to each other to find the optimum sound directivity. A series
of holes are provided to easily adjust the splay or tilt angle from 20° to 60° at an
increment of 2.5° between speakers.
Contents:
Be sure that all of the following items are included in this kit before proceeding:
2pcs
Joiner Plates
8pcs
Button head screw, M10X45mm
8pcs
Split lock washer, M10
8pcs
Flat Washer, M10
4pc
Eyebolt, M10x 35mm
Installing speakers must be performed by experienced professionals. If in doubt
about the integrity of the structure you are mounting or suspending to or not sure
about the proper hardware or method to use, consult a certified rigging company.
2010 ATM Fly-Ware, Signal Hill, CA 90755 (562) 424-1100
Rev. 00 -050510
Figure 1
Plates may differ per speaker model
FASPAC
TM
FP-EVH1152-2X1
2 WIDE X 1 DEEP PLANAR ARRAY CONFIGURATION
The FP-EVH1152-2X1 planar array kit gives
designers, contractors and audio consultants the
ability to create two EVH 1152 speakers in a tight
pack or splayed configurations. The FP-EVH1152-2x1
kit provides a method of flying a planar or line array
configuration while offering the capability of allowing
cabinet’s splay angle to be adjusted relative to each
other to find the optimum sound directivity. A series of
holes are provided to easily adjust the splay or tilt
angle from 20° to 60° at an increment of 2.5°
between speakers.
Installing speakers must be performed by
experienced professionals
. If in doubt about the
integrity of the structure you are mounting or
suspending to or not sure about the proper hardware
or method to use, consult a certified rigging company.
Package contents:
2 pcs
Joiner Plate
8 pcs
Button head screw, M10x45mm long
8 pcs
Split lock washer, M10
8 pcs Flat washer, M10
4 pcs Eyebolt, M10x 35mm long
1 pc Instruction Sheet
CAUTION:
PLEASE READ CAREFULLY BEFORE PROCEEDING
Due to the wide variety of building structures, materials and
suspension methods, these instructions assume that the
installing contractor/installer will exercise good judgment in
selecting the proper mounting area and hardware. As a guide,
the installation, when complete, should be capable of supporting
at least 5 times the actual load. Follow building code
requirements to safely suspend the speakers to the building
structure
2 WIDE X 1 DEEP PLANAR ARRAY:
Step 1:
Flip the two speakers so that the bottoms are facing up and lay
them side by side. Unscrew existing speaker screws where the
joiner plate will be installed. Discard removed screws.
Step 2:
Decide the splay angles of the loudspeaker cluster (Figure 1). Install the joiner plate on the speakers using the appropriate holes for the desired
loudspeaker splay angles. Use the provided M10 screws, flat washers and split washers. Do not tighten bolts until all joiner plates are installed
(Figure 2).
Figure 1
Figure 2
Installation Procedure:
Step 1:
Flip the two speakers so that the bottoms are facing up and lay
them side by side. Unscrew existing speaker screws where the joiner
plate will be installed. Discard removed screws.
Step 2:
Decide the splay angles of the loudspeaker cluster (Figure 1).
Install the joiner plate on the speakers using the appropriate holes for
the desired loudspeaker splay angles. Use the provided M10 screws,
fl at washers and split washers. Do not tighten bolts until all joiner
plates are installed (Figure 2).
Step 3:
Carefully fl ip the two speakers together so
that the top is facing up. Removed the screws in the
holes where the joiner plates are installed. Install
the joiner plates using the same holes as the bottom
joiner plates using the provided screw, split washer
and fl at washer (Figure 3).
Adaptive Technologies Group
1635 E. Burnett Street | Signal Hill, CA 90755 USA
Ph: 562.424.1100 | Fax: 562.424.3520
www.adapttechgroup.com
ALWAYS INSTALL SAFETY CABLES
WARNING:
Mounting and/or suspension of audio and video equipment requires
experienced professionals. Improperly installed loudspeakers can result in property
damage, personal injury and/or liability to the installing contractor.
