background image

3

Regulatory Compliance Statements

Federal Communications Commission Radio Frequency Interference Statement

WARNING: Changes or modifications to this unit not expressly approved by the party 
responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and 
can radiate radio frequency energy, and if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. However, if this 
equipment does cause interference to radio or television equipment reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is 
connected.

Consult the dealer or an experienced radio/television technician for help.

Use a shielded and properly grounded I/O cable and power cable to ensure compliance of 
this unit to the specified limits of the rules.

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference and (2) this device must accept 
any interference received, including interference that may cause undesired operation.

European Union Compliance Statement

This Information Technology Equipment has been tested and found to comply with 
EMC Directive 89/336/EEC, as amended by 92/31/EEC and 93/68/EEC, in 
accordance with:

EN55022 (1998) Emissions

EN55024 (1998) Immunity:

– EN61000-4-2 (1998) Electrostatic discharge: ±4 kV contact, ±8 kV air
– EN61000-4-3 (1998) Radiated immunity
– EN61000-4-4 (1995) Electrical fast transients/burst: ±1 kV AC, ±0.5 kV I/O
– EN61000-4-5 (1995) Surges ±1 kV differential mode, ±2 kV common mode
– EN61000-4-6 (1996) Conducted immunity: 3 V
– EN61000-4-11 (1994) Supply dips and variation: 30% and 100%

In addition, all equipment requiring U.L. listing has been found to comply with EMC 
Directive 73/23/EEC as amended by 93/68/EEC in accordance with EN60950 with 
amendments A1, A2, A3, A4, A11.

Canadian Compliance Statement

This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur 
le matériel brouilleur du Canada.

Adaptec, Inc.

ACS-100

Tested to Comply
With FCC Standards

FOR HOME OR OFFICE USE

Содержание ACS-100














Отзывы: