|
|
P a g e
P a g e
© Adam Equipment Company 2010
© Adam Equipment Company 2010
Show “Single” “123 C” with the left digit flashing. The user can use the
Show “Single” “123 C” with the left digit flashing. The user can use the
[PST/
[PST/
]]
key
key
to select another digit or the
to select another digit or the
[Dspl/
[Dspl/
]]
and
and
[Test/
[Test/
]]
to
to set
set the
the
temperature, Range is 050 C to 160 C
temperature, Range is 050 C to 160 C
“Ramp” Selected
“Ramp” Selected
Show “Ramp” the temperature as above for setting the temperature and then
Show “Ramp” the temperature as above for setting the temperature and then
change to
change to “Ramp Time” and
“Ramp Time” and “
“ XX:XX ”, minutes and
XX:XX ”, minutes and seconds.
seconds.
Use the
Use the arrow keys
arrow keys to select the digit
to select the digit to change.
to change. The user can
The user can select a time
select a time
up to 99:59.
up to 99:59.
The ramp time should be set long enough to allow the heater to warm the
The ramp time should be set long enough to allow the heater to warm the
sample gently.
sample gently.
“Step” Selected
“Step” Selected
Show “Step 1” and set the temperature of step one as for the single heat
Show “Step 1” and set the temperature of step one as for the single heat
settings above. When
settings above. When the value
the value is set the
is set the display will show
display will show “Time 1”
“Time 1” to set
to set
the
the time the
time the first step
first step is held.
is held. Enter the
Enter the value
value as
as above.
above. The minimum
The minimum time
time
for step 1 is 3 minutes.
for step 1 is 3 minutes.
When set press
When set press
[Setup/Enter]
[Setup/Enter]
to show
to show “Step 2”
“Step 2” and
and set this
set this temperature
temperature
and
and time
time and then
and then go
go to “Step
to “Step 3”
3” and
and set this
set this temperature and
temperature and time.
time.
If only 2
If only 2 steps are required set the
steps are required set the time for step 3
time for step 3 to 00:00.
to 00:00. The analyzer will
The analyzer will
ignore this setting.
ignore this setting.
Interval Setting
Interval Setting
The next setting will be to set the time interval the analyzer uses to determine
The next setting will be to set the time interval the analyzer uses to determine
results and to print the current result. The analyzer will compute the percent
results and to print the current result. The analyzer will compute the percent
SINGLE
SINGLE
ºC
ºC
123
123
RAMP
RAMP
ºC
ºC
123
123
RAMP TIME
RAMP TIME
10:00
10:00
RAMP TIME
RAMP TIME
06:00
06:00
Содержание PMB
