background image

EN • 3

ENGLISH

FRANCAIS

NEDERLANDS

ES

p

A

ño

L

IT

ALIAN

o

DE

u

TSCH

662Y0500 • B

Safety precautions

Please read these installation instructions carefully before commencing any installation work.
Liability and warranty claims will not be accepted for damage caused by failure to observe these 
installation instructions!

Faulty installation may result in injuries or property damage!

Working on the heating system: 

-   Installation,  commissioning, maintenance and repairs 

to the burner should be carried out only by an 
authorized specialist heating company.

When working on the burner and boiler:  -  Switch off the heating emergency shut-off switch 

and ensure that it cannot be switched on again.

 

-  Shut off the oil supply line and ensure that it cannot 

be accidently opened.

StandardS  
and directiVeS

The burner must be installed and 
operated in accordance with the 
following standards and directives.

HEIZAnIV

The German Heating Installations 
Ordinance

EN 303, Part 1 and Part 2

Heating boilers with forced draught 
burners

EN 60335, Part 1

Household and similar electrical 
appliances - Safety

DIN EN 267

Atomizing oil burners – Definitions, 
requirements, construction and testing

DIN 4755

Oil firing installations – Construction, 
design, safety requirements

DIN 51603, Part 1

Extra-light heating oils

Please observe regional building 
regulations.

exhauSt gaS SyStem 
and effectiVe heat 
requirement

Boiler, burner and exhaust gas system 
(chimney) form one operational unit. 
In the event of a power reduction, 
allowances must be made for low 
exhaust gas temperatures.

The system must be designed to avoid 
damage caused by condensate created 
when exhaust gas temperatures fall 
below 160°C.

we recommend installing a draught 
limiter (secondary air device) to obtain 
consistent combustion values and 
minimize potential humidity.
Ideally, this should be installed in the 
chimney to avoid any noise in the flue 
tube.

nozzle  
Selection

Please note that a correct, low-emission 
burn can be achieved only with nozzles 
that match the burner. The nozzles listed 
on page 13 are approved for use with 
the BMR burner.
All data on page 13 is recorded at 
maximum excess pressure.

StandaRdS and RegulatIonS

Содержание BMR 33















Отзывы: