background image

 

 
I. INITIAL SET-UP 
 

● Carefully remove the analyzer from the shipping box 
 
● Inspect the analyzer for any sign of shipping damage 
 

Contact Agtron immediately if any damage is apparent. A shipping claim for damage needs to be filed as 
soon as possible.

  

 
IMPORTANT: 

Keep the box and all packing material. Any unit returned to Agtron

 

for service must be 

shipped in the original packaging or Agtron will not accept the unit.

 

 

The carton contains the following items:   
                                                        
- E20CP-III Analyzer 
- Power Cord 
- Large Diameter Yellow Life Disk 
- Two Plastic Sample Dishes 
- Smaller Diameter Two-Sided Red / Black Calibration Disk & Dish Set 
- Rectangular Metal Sample-Dish Tray 
- This Operation Manual 

 

● Place the Agtron analyzer on a clean level surface 
 
● Keep the cooling fan vent on the back of the unit free of obstruction 
 
● Avoid placing the unit where it will be in direct sunlight  
 
● Fully-open the sample drawer by pulling it straight out until it hits the bumper stop 
 
● Look into the chassis under the drawer. There are four posts sticking up from a raised platform that is affixed 
to the inside bottom of the chassis. Place the large diameter Yellow Life Disk between the four posts so that it 
sits flat on the platform.  
 
● Place the rectangular metal sample-dish tray into the cutout on the sample drawer top surface by first placing 
the front of the tray with the thinnest edge facing forward against the rubber locating bumpers, then push the 
back edge of the tray down into the opening so that the tray recesses fully into the cutout and the side flanges of 
the tray sit flat on the drawer top surface. 
 

NOTE:

 The sample-dish tray should always remain in the analyzer sample drawer. It should only be removed 

for periodic cleaning. Always keep the sample drawer in the fully closed position when not in use. 
 
● Fully close the sample drawer 
 
● Connect the AC power cord to its mating socket on the back of the unit. Make certain that the plug is firmly 
seated  
 
● Connect the unit to AC mains power 

 

Содержание E20CP-III


























Отзывы: