ActionTec DataLink V.90 FM560LKI Скачать руководство пользователя страница 32

Страница: 32 / 63

Result Codes:

n = 0, 1

ERROR

Otherwise

Result Code Option

W0:

CONNECT result code reports DTE speed. Disable protocol result codes.

W1:

CONNECT result code reports DTE speed. Enable protocol result codes.

W2:

CONNECT result code reports DCE speed. Enable protocol result codes

(default).

Result Codes:

n = 0, 1, 2

ERROR

Otherwise

Result Code Selection and Call Progress Monitoring

This command enables tone detection options used in the dialing process. As these

functions are chosen, the modem chipsets result codes are also affected. There-

fore, this command is frequently used to control the modem chipsets responses.

The primary function of this control is to control the modem chip sets call re-

sponse capabilities.

Extended Result Codes

Disabled: Displays only the basic result codes OK, CONNECT, RING,

NO CARRIER, and ERROR.

Enabled: Displays basic result codes, along with the connect message

and the modems data rate, and an indication of the modems

error correction and data compression operation.

Dial Tone Detect

Disabled: The modem dials a call regardless of whether it detects a dial

tone. The period of time the modem waits before dialing is speci-

fied in register S6.

Enabled: The modem dials only upon detection of a dial tone, and dis-

connects the call if the dial tone is not detected within 10 sec-

onds.

Содержание DataLink V.90 FM560LKI
































































Результаты поиска

Содержание DataLink V.90 FM560LKI

Отзывы:

Бренды по названию

Популярные бренды

ActionTec DataLink V.90 FM560LKI, Руководство пользователя

Результаты поиска

Содержание DataLink V.90 FM560LKI

Отзывы:

Бренды по названию

Популярные бренды