Action ARUNDEL TWIN Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 21

Action ARUNDEL TWIN Скачать руководство пользователя страница 11

Attaching the Commando Net:

ATTENTION: Allow a minimum of 2 metres space around the play centre and ensure that the area
is free from other obstacles such as trees and branches, garden lights and other play equipment.

If you are building a single tower, the diagram does not show the sandpit for clarity. Attach the top
rail (part A) to the two uprights of the tower. Using 2 x m10 x 110mm bolts, washers and nuts. Tie
the commando net to the top rail, making sure the gap between the top rung is of the net and the
rail is less than 90mm. Use a double knot on each rope to give extra strength. now fill the bottom rail
(part B)with 4 x 60mm screws. When fitting the lower commando net rail (part B) first remove the
bottom sandpit side. Lay the beam in its correct position, mark with a spade and dig out a shallow
trench. Lay the beam into this trench and screw firmly in place. Any gaps under the beam should be
re-filled with soil or sand and pack firmly, but before doing so attach your commando net, again
using a double knot.

BEWARE: When tying the ropes to the top commando rail (part A) make sure that the gap
between the top rung of the net is even and the gap less than 9cm to avoid accidental head
entrapment.

«
...
9
10
11
12
13
...
»

Содержание ARUNDEL TWIN






















Отзывы:

Нет отзывов