ACTi Z71 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 23

background image

www.acti.com

Hardware Manual

8

Package Contents

Contact your local dealer if the package is damaged or incomplete.

Camera

Cable Gland

with Rubber and Washer

Wrench

Mounting Screw Kit

Drill Template

Quick Guide &

Warranty Card

IMPORTANT:

When the camera is taken out from the box, the lens and sensor are covered by

thin film. DO NOT remove these films. It is used to protect the lens and sensor from scratches

or fingerprint marks which may happen during installation. Remove the film only after the

camera is securely installed and all connections are complete.

Drill Template

Warranty Card

«
...
6
7
8
9
10
...
»

Содержание Z71
























Отзывы:

Нет отзывов

Похожие инструкции для Z71

Welcome M21311P1-A

Бренд: ABB Страницы: 15

Бренд: Cam Scan Страницы: 7

Бренд: EverFocus Страницы: 12

Бренд: RED SHIELD Страницы: 25

Бренд: Arcteq Страницы: 122

Бренд: Speco Страницы: 2

Бренд: EverFocus Страницы: 2

Бренд: Northern Страницы: 2

Бренд: König Страницы: 51

Бренд: Majorcom: Страницы: 15

Бренд: ZowieTek Страницы: 24

Бренд: Waeco Страницы: 216

Бренд: Inovonics Страницы: 2

Бренд: Axis Страницы: 42

Бренд: Duevi Страницы: 19

Surveillance Detector

Бренд: Mini Gadgets Страницы: 2

Бренд: ANALOX Страницы: 16

Бренд: schmersal Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды