background image

www.acti.com

Installation Guide 

       

18 

Safety Information 

Read these instructions 

You should read all the safety and operating instructions before using this product.   

 

Heed all warnings 

You must adhere to all the warnings on the product and in the instruction manual. Failure to follow 

the  safety  instruction  given  may  directly  endanger  people,  cause  damage  to  the  system  or  to 

other equipment.   

 

Trademarks 

All names used in this manual are probably registered trademarks of respective companies.   

 

Liability 

Every reasonable care has been taken during the writing of this manual. Please inform your local 

office  if  you  find  any  inaccuracies  or  omissions.  We  cannot  be  held  responsible  for  any 

typographical  or  technical  errors  and  reserve  the  right  to  make  changes  to  the  product  and 

manuals without prior notice.   

 

Cleaning 

Disconnect this video product from the power supply before cleaning. 

 

Attachments 

Do not use attachments not recommended by the video product manufacturer as they may cause 

hazards. 

 

Do not use accessories not recommended by the manufacturer 

Only install this device in a dry place protected from weather   

 

Servicing   

Do not attempt to service this video product yourself. Refer all servicing to qualified service 

personnel. 

 

 

 

Содержание KCM-5*11E




















Отзывы: