5
6
We need know about you. Send your suggestions
[email protected]
If you have any question about our products,
please visit our web site.
How to use the wheel
Your mouse has a wheel that functions both as a
wheel for Windows scrolling and also as a
customized button. It can be used as a standard
mouse button, click (press down) the wheel. To
Use the Middle Button, Directly Press down the
Wheel. For scrolling the screen, simply move the
wheel.
TROUBLESHOOTING
Wireless Mouse Troubleshooting
A. Mouse does not upon intallation
Try one more of the following:
1) For optimal performance, place adjust the
angle of the receiver to find the best
performance.
2) Make sure you have installed the batteries
correctly. Press the “Channel Reset” button on
the receiver and then press the “Channel Reset”
button on the mouse.
B. Mouse not detected:
When using the mouse, it may not be delected by
the computer or receiver. To remedy this problem
try the following
1) Make sure the receiver is plugged into the
right mouse port or USB port.
2) Make sure your mouse port has the proper
configuration. Refer to your computer
documentation for the correct port configuration.
3) You may re-setup the connetion RF Channel
between the mouse and the Receiver, especially,
when you have been changed or recharged your
batteries.
C. The Screen Cursors Does Not Move
Property:
1) Change the angle of your radio receiver. Try
adjusting the receiver and/or mouse to improve
reception.
2) Make sure thar the battery low indicator is
NOT lit on. Replace batteries if the low battery
indicator is lit on.
You may also need to change the RF Channel for
the mouse, press the “Channel Reset” button on
the receiver, then press the “Channel Reset”
button on the mouse.
D. Mouse does not work upon installation.
Try one or more of the following:
1)Make sure you have installed the Driver
correctly.
2) Make sure the receiver cabe is plugged into
the right mouse port or USB port.
GENERAL FEATURES
- Ergonomic Design
- Super Grip Coating
- Rechargeable by base
- Wireless Frequency 27MHz
- 1 Channel and 256 ID's
- Operation Range 1.5m
- 3 power save modes
- Plug and Play, no driver required
- Programmable buttons with optional driver
- Optical Tracking Engine
- 800 dpi resolution
- 5 B Scroll Wheel
- Dimensions 120 mm x 69 mm x 40 mm
- USB Interface
- Operation Temperature 41 - 104 °F
- Operation Humidity 20 90%
- Compatible with Windows
98/98SE/ME/2000/XP
- Compatible with Macintosh 8.6 or higher
Federal Communication Commission
Interference Statement
This equipment has been tested and found to
with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off andon, the user is
encouraged to try to correct the interference
by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
3) Unplug the receiver and then plug in the
receiver again. Make sure that it had been
detected by the Operating Systems properly.
4) Make sure your mouse port has the proper
configuration. Refer to your computer
documentation for the correct port configuration.
Receiver Troubleshooting
Receiver does not work before the installation.
Try one or more of the following:
1. Make sure you have installed the Driver
correctly.
2. Make sure the cable is plugged into the right
mouse port.
3. Unplug the Receiver and then plug the mouse
again.
4. Make sure that Receiver had been detected by
the Operating Systems properly. Make sure your
mouse port has the proper configuration. Refer to
your computer documentation for the correct port
configuration.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference,
and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
FCC Caution: Any changes or modifications
not expressly approved by the party
responsible for compliance could void the
user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. To maintain compliance with FCC
RF exposure compliance requirements, please
avoid direct contact to the transmitting antenna
during transmitting. End users must follow the
specific operating instructions for satisfying RF
exposure compliance.
This transmitter must not be co-located or
operating in conjunction with any
other antenna or transmitter.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
CE - Type acceptance: EN300 328 FHSS Device
SYSTEM REQUIREMENT
Mouse compatible with standard Microsoft OS
3rd button and wheel function require Win98/
ME/ 2000/ XP. If your computer's operating
system is Windows 98/ 98SE, please prepare the
Windows98 or 98SE compact disk for system's
request during the installation of mouse
