ACT ACT-VCC-5000 Скачать руководство пользователя страница 17

Rev A 

 

ACT-VCC-5000-AC) 

 

  

 

 

 

 

17 

 

7.2 Service and Repair 

Warranty period

:

 1-year limited warranty 

 
Warranty Section from ACT’s PURCHASE ORDER TERMS AND CONDITIONS 

 

 

Buyer’s Property.

 All drawings, tools, fixtures, materials and other items supplied or paid for by Buyer 

shall be and remain the property of Buyer. All such items shall be used only in the performance of work 

under this Order unless Buyer consents otherwise in writing. Seller shall have the obligation to maintain 

any and all property furnished by Buyer to Seller and shall be responsible for all loss or damage to said 

property except for normal wear and tear. 

 

Warranty.

 Seller warrants that all Goods furnished under this Order shall conform to all specifications 

and appropriate standards, will be new, and will be free from defects in material or workmanship. Seller 

warrants that all Goods furnished hereunder will be merchantable, and will be safe and appropriate for 

the purpose for which Goods of that kind are normally used. If Seller knows or has reason to know the 

particular purpose for which Buyer intends to use the Goods, Seller warrants that such Goods will be fit 

for such particular purpose. Inspection, test, acceptance or use of Goods furnished hereunder shall not 

affect Seller’s obligations under this warranty, and such warranty shall survive inspection, test, 

acceptance and use. Seller’s warranty shall run to Buyer, its successors, assigns and customers, and 

users of products sold by Buyer. Seller agrees to replace or correct defects of any Goods not 

conforming to the foregoing warranty promptly, without expense to Buyer, when notified of such 

nonconformity by Buyer, provided that Buyer elects to provide Seller with an opportunity to do so. In the 

event of failure of Seller to correct defects in or replace nonconforming Goods, Buyer, after reasonable 

notice to Seller, may make such corrections or replace such Goods and charge Seller for the costs 

incurred by Buyer in doing so. Seller shall be liable for and save Buyer harmless from any loss, damage, 

or expense whatsoever that Buyer may suffer from a breach of these warranties. 

 

Inspection and Acceptance.

 All Goods are subject to Buyer’s inspection, testing and approval, both at 

Seller’s facility and Buyer’s point of destination. Buyer reserves the right to reject and refuse acceptance 

of any Goods which do not comply with all the terms of this Order. Acceptance, payment, use, or resale 

of Goods by Buyer shall not release Seller of any of Seller’s obligations, representations, or warranties 

hereunder. Payment for any Goods shall not be deemed an acceptance hereof. 

 
Please see ACT’s current full Terms & Conditions:

 

https://www.1-act.com/termsandconditions/

 

 

Disclaimer 

The warranty is limited to the delivered product(s) and ACT is not responsible for any loss that may be derived 

by equipment failure. 

 

 

 

Содержание ACT-VCC-5000



















Отзывы: