Acrosser Technology AR-B1476 Скачать руководство пользователя страница 49

Страница: 49 / 59

AR-B1476 User

’

s Guide

6-7

6.5 PERIPHERAL SETUP

This section is used to configure peripheral features.

AMIBIOS SETUP - PERIPHERAL SETUP

OnBoard

FDC Enabled

OnBoard

Serial

Port1

3F8

OnBoard Serial Port1 IRQ

OnBoard

Serial

Port2

2F8

OnBoard Serial Port2 IRQ

OnBoard

Parallel

Port

378

Parallel

Port

Mode

Normal

EPP

Version

N/A

Parallel

Port

IRQ

Parallel Port DMA Channel

N/A

OnBoard

PCI

IDE

Both

Available Options :

Auto
Disabled
Enabled

ESC:Exit

↑↓

:Sel

PgUp/PgDn:Modify
F2/F3:Color

Figure 6-5 BIOS: Peripheral Setup

OnBoard FDC

This option enables the floppy drive controller on the AR-B1476.

OnBoard Serial Port

This option enables the serial port on the AR-B1476.

OnBoard Parallel Port

This option enables the parallel port on the AR-B1476.

Parallel Port Mode

This option specifies the parallel port mode. ECP and EPP are both bi-directional data transfer schemes that
adhere to the IEEE P1284 specifications.

Parallel Port DMA Channel

This option is only available if the setting for the parallel Port Mode option is ECP.

OnBoard PCI IDE/IDE Prefetch

This option specifies the onboard IDE controller channels that will be used.

6.6 AUTO-DETECT HARD DISKS

This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard
CMOS Setup screen.

Содержание AR-B1476




























































Результаты поиска

Содержание AR-B1476

Отзывы:

Похожие инструкции для AR-B1476

Бренды по названию

Популярные бренды

Acrosser Technology AR-B1476, Руководство пользователя

Результаты поиска

Содержание AR-B1476

Отзывы:

Похожие инструкции для AR-B1476

Бренды по названию

Популярные бренды