Acrosser Technology AR-B1476 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 59

background image

AR-B1476 User

’

s Guide

5-1

5. INSTALLATION

This chapter describes the procedure of the utility diskette installation. The following topics are covered:

z

Overview

z

Utility

Diskette

z

Watchdog

Timer

5.1 OVERVIEW

This chapter provides information for you to set up a working system based on the AR-B1476 CPU board. Please
read the details of the CPU board’s hardware descriptions before installation carefully, especially jumpers’ setting,
switch settings and cable connections.

Follow steps listed below for proper installation:

Step 1 :

Read the CPU card’s hardware description in this manual.

Step 2 :

Install any DRAM SIMM onto the CPU card. (or user can skip this step because that the AR-B1476
embedded on-board DRAM)

Step 3 :

Set jumpers.

Step 4 :

Make sure that the power supply connected to your passive CPU board backplane is turned off.

Step 5 :

Plug the CPU card into a free AT-bus slot or PICMG slot on the backplane and secure it in place with
a screw to the system chassis.

Step 6 :

Connect all necessary cables. Make sure that the FDC, HDC, serial and parallel cables are
connected to pin 1 of the related connector.

Step 7 :

Connect the hard disk/floppy disk flat cables from the CPU card to the drives. Connect a power
source to each drive.

Step 8 :

Plug the keyboard into the keyboard connector.

Step 9 :

Turn on the power.

Step 10:

Configure your system with the BIOS Setup program then re-boot your system.

Step 11:

If the CPU card does not work, turn off the power and read the hardware description carefully again.

Step 12:

If the CPU card still does not perform properly, return the card to your dealer for immediate service.

5.2 UTILITY DISKETTE

AR-B1476 provides two VGA driver diskettes. It supports WIN31, WIN95, WINNT 4.0 and OS/2. If your operating
system is the other operating system, please attach Acrosser that will provide the technical supporting for the VGA
resolution.

There are two diskettes: disk 1 is for WIN31, WIN95 & WINNT4.0 VGA resolution; disk 2 is for OS/2 VGA
resolution. While user extracted the compressed files there is the README.* file in each sub-directories. Please
refer to the file of README for any troubleshooting before install the driver.

«
...
35
36
37
38
39
...
»

Содержание AR-B1476




























































Отзывы:

Нет отзывов

Похожие инструкции для AR-B1476

Бренд: Datavan Страницы: 15

Бренд: ASROCK Страницы: 128

Бренд: ECS Страницы: 56

Бренд: MATSONIC Страницы: 76

Бренд: Aaeon Страницы: 40

Бренд: Gigabyte Страницы: 104

Бренд: Texas Instruments Страницы: 21

Бренд: Gigabyte Страницы: 40

Бренд: DFI Страницы: 107

Бренд: Micronics Страницы: 63

SR1500AL - Server System - 0 MB RAM

Бренд: Intel Страницы: 180

Бренд: Ublox Страницы: 2

Бренд: MSI Страницы: 106

Thunder HEsl S2567

Бренд: TYAN Страницы: 60

Бренд: DFI Страницы: 149

Бренд: AOpen Страницы: 8

Бренд: ASROCK Страницы: 26

SY-KT333 DRAGON Plus

Бренд: SOYO Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды