Acromag Vertu Series Скачать руководство пользователя страница 6

Страница: 6 / 47

Vertu Series VPM3000 Process Meters & Temperature Transmitters

Instruction Manual

Introduction

The Vertu digital panel meter is one of the most

versatile digital panel meters on the market and will

satisfy a wide variety of process and temperature

applications. The Vertu can be field programmed to

accept process voltage (0-5V, 1-5V, etc) and current

(4-20 mA) inputs, 100 Ohm RTDs, and the four most

common thermocouples types.
One of the Vertu’s most useful features is its ability

to provide 24 VDC to power the transmitter’s 4-20 mA

signal. This reduces costs and simplifies wiring. The

Vertu is housed in a shallow-depth, 1/8 DIN enclosure

that features a NEMA 4X front panel and convenient

mounting hardware. There are two power options for

the Vertu: 85 to 265 VAC or 12-36 VDC and certain

configurations of the AC powered meter can provide 24

VDC to power the transmitter, if needed. Programming

and setup can be performed with the four front panel

pushbuttons, free DisplayWizard software or using the

Copy function.
Two relays and isolated 4-20 mA output options

increase the utility of the Vertu meter. The relays can

be used for alarm or control applications. The 4-20 mA

output provides an isolated retransmission of the input

signal; especially useful for temperature inputs like

thermocouples and RTDs.
The display height on the Vertu VPM3000 is an

astounding 1.2" (30.5 mm) and can be read easily from

distances of up to 30 feet!
The intensity of the display on the Vertu can be

adjusted to compensate for various lighting conditions,

especially direct sunlight.

Ordering Information

Vertu Large Display Options

85-265 VAC

Model

12-36 VDC

Model

Options Installed

VPM3100

VPM3200

No options

VPM3101

24 V supply

VPM3130

VPM3230

2 relays

VPM3131

2 relays, 24 V supply

VPM3110

VPM3210

4-20 mA output

VPM3111

4-20 mA output,

24 V supply

VPM3112

4-20 mA output,

dual 24 V supplies

VPM3220

2 relays, 4-20 mA output

VPM3121

2 relays, 4-20 mA output,

24 V supply

Accessories

Model

Description

ACC1000

USB Serial Adapter for Panel Meter

Programming

ACC1001

Isolated RS-232 to RS-422/485

Converter

ACC1002

Non-Isolated USB to RS-232

Converter

ACC1003

Isolated USB to RS-485 Converter

APMA7420

Standard Modular Cable, 7' (2.1 m)

APMA7422

RS-422/485 Serial Adapter with Cable

APMA7420 included

APMA7232

RS-232 Serial Adapter with Cable

APMA7420 included

APMA6845-SS Stainless Steel Pipe-Mounting Kit

for APMA2801

APMA2801

NEMA 4X Polycarbonate Enclosure

for 1 Meter

DisplayWizard

DisplayWizard software download at

www.acromag.com

Содержание Vertu Series
















































Результаты поиска

Содержание Vertu Series

Отзывы:

Похожие инструкции для Vertu Series

Бренды по названию

Популярные бренды

Acromag Vertu Series, Инструкция по эксплуатации

Результаты поиска

Содержание Vertu Series

Отзывы:

Похожие инструкции для Vertu Series

Бренды по названию

Популярные бренды