Acromag DT333-0700 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 37

background image

Model DT333-0700

4-Wire mV/TC Dual Transmitter w/USB

Acromag, Inc. Tel: 248-295-0880

- 10 -

http://www.acromag.com

- 10 -

https://www.acromag.com

Optional Bus Power Connections

TIP:

How many units may share a

bussed connection to power?  This
device consumes up to 1.6W.  For
a bussed power connection, it is
recommended that you fuse-limit
the maximum supply current to 3A
or less including inrush.  The turn-
ON inrush current may peak up to
twice its DC value.  To calculate
the safe maximum number of units
that can share this supply
connection, multiply 1.5A and your
supply voltage and divide the
result by 1.6W.  For this model,
this is roughly equivalent to the
number of supply volts.  That is, a
24V supply fused with 3A may
drive 24 units safely.

Power is normally wired to the TB5 terminals of the unit as shown on the previous
page. However, this device is equipped to be optionally or redundantly powered via
a DIN rail bus connector (Acromag 1005-063) mated to an optional plug-in terminal
block (Acromag 1005-220 or 1005-221, depending on left or right-side wire entry).
Any power input via the bus connector is diode-coupled to the same point in the
circuit as unit power connected at power terminal TB5. You could power multiple
units by snapping them together along the DIN rail bus using connector 1005-063,
then connecting a mating terminal block (select a Left or Right-side connector, see
figure below). While the intent of the bus power connector is to allow several units
to conveniently share a single supply, you could also use the bus power connector
to redundantly power units (with local power also applied at TB5), allowing a
backup supply to maintain power to the units should the main supply at TB5 fail.

Acromag TTBUS-KIT connector kit contains bus connector 1005-063, plus left-side
terminal 1005-220, and right-side terminal 1005-221, allowing units to snap
together, side-by-side, along the DIN rail and share the power connection.

Important

–

End Stops:

If this module uses the optionally powered (or redundantly

powered) via the DIN rail bus for hazardous location installations (Class I, Division 2
or ATEX/IECEx Zone 2) it should use two end stops (like Acromag 1027-222) to
secure the terminal block and module (not shown).

Optional Bus Power
Connections

…

The figure below shows how to wire power to the optional bus terminal block when
mated to the bus connector. Note that power is wired to the rightmost bus
terminals on the right, or the left-most terminals on the left. Observe proper
polarity.

!

«
...
8
9
10
11
12
...
»

Содержание DT333-0700






































Отзывы:

Нет отзывов

Похожие инструкции для DT333-0700

Бренд: Nautel Страницы: 229

Бренд: Nautel Страницы: 18

Бренд: Nautel Страницы: 326

Бренд: Z-Wave Страницы: 2

Бренд: Novus Страницы: 2

Бренд: Camel RF Electronic Страницы: 5

Бренд: Yaesu Страницы: 165

Бренд: M-system Страницы: 3

Бренд: Epoch Страницы: 17

Centronic / B-Tronic EasyControl EC715

Бренд: Becker Страницы: 144

Бренд: Icom Страницы: 28

Бренд: Intek Страницы: 36

Бренд: Intek Страницы: 36

Бренд: Kongsberg Страницы: 26

Бренд: CYP Страницы: 16

Бренд: MTT Страницы: 4

SINEAX DME 4 Series

Бренд: Gossen MetraWatt Страницы: 36

Бренд: Extron electronics Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды