background image

Y1-03-0250 Rev. B 

24 

CAUTION: 

Do  not  force  the  lid  closed.  If  the  lid  does  not  close  easily, 

check  to  see  that  the  beacon  is  properly  installed  in  the  bracket  and  the 
HydroFix™ is properly seated.  

9. 

Servicing the QuickDraw

™  

To 

remove a beacon from the Category II bracket, press the “PUSH” lever to 

release  the  beacon  from  the  bracket.  The  beacon  will  now  be  able  to 
forward and down out of the bracket. 
 
It  is  not  anticipated  that  the  QuickDraw

™ 

will  require  servicing  other  than 

cleaning or, rarely, replacement.

 

 

 
 

NOTE:

 Whenever a beacon is returned for service, it must be accompanied 

by the bracket. 
 

10. 

Self-Testing the beacon 

The  Satellite

3

 

406™  beacon  may  be  self-tested  as  is  warranted,  up  to  a 

maximum of sixty times in the five-year life of the battery, or once per month 
for  the  life  of  the  battery.  Self-Tests  can  be  performed  randomly,  however, 
ACR  recommends  that  you  perform  the  Self-Test  on  a  once  per  month 
schedule. Do not exceed sixty (60)  Self-Test cycles limit in the five-year life 
of the battery, to conserve the battery for emergency use.

 

 
The  functional  Self-Test  is  initiated  by  momentarily 
lifting  the  Activation  Switch  to  a  vertical  position  and 
holding it in this position for at least one second and at 
most  four  seconds.  A  beep  indicates  the  initiation  of 
the  Self-Test  sequence.  Self-Test  will  check  battery 
capacity and perform four functional test sequences as 
described below. 
 

TEST   

 

SUCCESS 

 

FAIL 

EEPROM Connect  

Beep, Green LED  

Test Stopped,   Red LED  

Lock Circuit  

Beep, Green LED  

Test Stopped,   Red LED  

Signal Strength  

Beep, Green LED  

Test Stopped,   Red LED  

Locator Light  

Beep, Green LED, Strobe  

Test Stopped,   Red LED  

Summary  

Green LED  

 

 

 
The last green LED indicates a successful test. If any of the individual tests 
fail during Self-Test, there will be two beeps and a red LED flash at the end 
of the Self-Test. Self-Test will discontinue at that point. 
 

NOTE:

 

The “beeps” are a very high-pitched tone that some people may not 

be able to hear. You may count the green LED flashes.  
 
 
 

Содержание RLB-38 2874
































Отзывы:

Похожие инструкции для RLB-38 2874