background image

FIXTURE

MOUNTING

SCREW 

FIXTURE TAB

SLOT

SCREW LOCATION

CONDUIT

7CM FROM

CENTER

TOP

3

2

Figure 1

1. Input voltage is AC12V. The lamps must be connected with transformer.

2. The junc�on box is located at least 1200mm from the edge of the pool.

3. The moun�ng bracket must be properly installed so that the top edge of the

light’s lens is at least 450mm below the water level in the pool. see Figure 1.

4. Make sure the  surface of pool wall is flat.

Fix the bracket with 4pcs screws.

5.

 If the cable connec�on is done underwater, the connec�on part must be 

waterproof protected  

(use waterproof cable gland or fill with epoxy glue). 

Otherwise, the water will come in the lamp through the wires.

6.

Connect all wires to the corresponding circuit wires in the junc�on box and

feed epoxy.

7.

Before opera�ng the light for more than 10 seconds fill pool un�l the light is

completely submerged in water.

8. It is easy to replace the lamp.

MINI 1200mm

250mm

Rigid conduit

Junc�on Box

Water Level

Mini. from bo�om of 

J.B. to water level

From water level to top of lens

Wall surface

Pool body

450mm

300mm

DIMENSION

INSTALLATION

180mm

38mm

Posición libre

Posición bloqueada

FIXTURE

MOUNTING

SCREW 

FIXTURE TAB

SLOT

SCREW LOCATION

CONDUIT

7CM FROM

CENTER

TOP

3

2

Figure 1

1. Input voltage is AC12V. The lamps must be connected with transformer.

2. The junc�on box is located at least 1200mm from the edge of the pool.

3. The moun�ng bracket must be properly installed so that the top edge of the

light’s lens is at least 450mm below the water level in the pool. see Figure 1.

4. Make sure the  surface of pool wall is flat.

Fix the bracket with 4pcs screws.

5.

 If the cable connec�on is done underwater, the connec�on part must be 

waterproof protected  

(use waterproof cable gland or fill with epoxy glue). 

Otherwise, the water will come in the lamp through the wires.

6.

Connect all wires to the corresponding circuit wires in the junc�on box and

feed epoxy.

7.

Before opera�ng the light for more than 10 seconds fill pool un�l the light is

completely submerged in water.

8. It is easy to replace the lamp.

MINI 1200mm

250mm

Rigid conduit

Junc�on Box

Water Level

Mini. from bo�om of 

J.B. to water level

From water level to top of lens

Wall surface

Pool body

450mm

300mm

DIMENSION

INSTALLATION

180mm

38mm

Posición libre

Posición bloqueada

FIXTURE

MOUNTING

SCREW 

FIXTURE TAB

SLOT

SCREW LOCATION

CONDUIT

7CM FROM

CENTER

TOP

3

2

Figure 1

1. Input voltage is AC12V. The lamps must be connected with transformer.

2. The junc�on box is located at least 1200mm from the edge of the pool.

3. The moun�ng bracket must be properly installed so that the top edge of the

light’s lens is at least 450mm below the water level in the pool. see Figure 1.

4. Make sure the  surface of pool wall is flat.

Fix the bracket with 4pcs screws.

5.

 If the cable connec�on is done underwater, the connec�on part must be 

waterproof protected  

(use waterproof cable gland or fill with epoxy glue). 

Otherwise, the water will come in the lamp through the wires.

6.

Connect all wires to the corresponding circuit wires in the junc�on box and

feed epoxy.

7.

Before opera�ng the light for more than 10 seconds fill pool un�l the light is

completely submerged in water.

8. It is easy to replace the lamp.

MINI 1200mm

250mm

Rigid conduit

Junc�on Box

Water Level

Mini. from bo�om of 

J.B. to water level

From water level to top of lens

Wall surface

Pool body

450mm

300mm

DIMENSION

INSTALLATION

180mm

38mm

Posición libre

Posición bloqueada

Отзывы: