ACP P1330201M Скачать руководство пользователя страница 18

Страница: 18 / 33

Testing Procedures

WARNING

To avoid risk of electrical shock, personal injury

or death; disconnect power to oven and discharge capacitor

before servicing, unless testing requires power.

ACP, Inc.

16023293 Rev. 0

Illustrati on

Component

Testing

Results

Interlock switch assembly

Primary

Monitor

Secondary

Disconnect wires to switch.

With door open measure resistance from:

Monitor - Terminal 3 - 4..........................

Primary - Terminal 1 - 2 .........................

Secondary - Terminal 5 - 6 .....................

With door closed measure resistance from:

Monitor - Terminal 3 - 4..........................

Primary - Terminal 1 - 2 .........................

Secondary - Terminal 5 - 6 .....................

After verifying or replacing the

module, reconnect wires to switch

and check operation of monitor circuit

before operating the oven.

Indicates continuity

Infinite

Ω

Infinite

Ω

Infinite

Ω

Indicates continuity

Lamp receptacle

Test continuity of receptacle terminals.

Indicates continuity with bulb

installed.

Wire Harness

Test continuity of wires

Indicates continuity

Electronic Control Panel

Service Test Mode:

Open door, Press and Hold pad 3 for 5

seconds to enter service test mode.

Press Pad 1 ................................................

Press Pad 2 ................................................

Press Pad 3 ................................................

Press Pad 4 ................................................

Press Pad 5 ................................................

Press Pad 6 ................................................

Press Pad 7 ................................................

Press Pad 8 ................................................

Press Pad 9 ................................................

Press Pad 0 ................................................

Stop/Reset Pad ...........................................

SERVICE appears in the display

Indicates number of hours

magnetron has been turned on

Indicates number of times

magnetron tube has been turned

on and off

Indicates number of door cycles

CLEAR (Press START pad to

reset service data.)

Indicates amperage

N/A

RESET (Clear Service Alarm)

N/A

Exit Service Test Mode

Error codes:

E-08

............................................................

E-09 ............................................................

E-10 ............................................................

Replace Control Board

Shorted or Open Keypad – Test

and replace if necessary

Electronic Dial Control Panel

START

DEFROST

50%

70%

Hidden

Pad 1

Hidden

Pad 2

Service Test Mode:

Open door, Press and Hold Hidden Pad

2 for 5 seconds to enter service test

mode.

Press Hidden Pad 2 ....................................

Press Hidden Pad 2 again

.........................

Press Hidden Pad 2 again

.........................

Press Hidden Pad 2 again

.........................

Press Hidden Pad 2 again

.........................

Press Hidden Pad 2 again

.........................

Enters into Service Test Mode

Indicates number of magnetron

hours

Indicates tube cycles

Indicates number of door cycles

Indicates amperage

Turn dial to Clear Info – When

dial is rotated display indicates

CLEARED INFO

Содержание P1330201M


































Результаты поиска

Содержание P1330201M

Отзывы:

Похожие инструкции для P1330201M

Бренды по названию

Популярные бренды

ACP P1330201M, Сервисная инструкция

Результаты поиска

Содержание P1330201M

Отзывы:

Похожие инструкции для P1330201M

Бренды по названию

Популярные бренды