background image

Chapter 2                                                          4845GVM(V3.1) BIOS Setup

2-51

IRQ Resources

When resources are controlled manually, assign each system

interrupt a type, depending on the type of device using the

interrupt.

PCI / VGA Palette Snoop

Choose Disabled or Enabled. Some graphic controllers which

are not VGA compatible take the output from a VGA controller

and map it to their display as a way to provideboot information

and VGA compatibility.

However, the color information coming from the VGA controller

is drawn from the palette table inside the VGA c o n t r o l l e r   t o

generate the proper colors, and the graphic controller needs to

know what is in the palette of the VGA controller.  To do this,

the non-VGA graphic controller  watches for the write access to

the VGA palette and registers the snoop data.  In PCI based

systems, the Write Access to the palette will not show up on the

ISA bus if the PCI VGA controller responds to the Write.

In this case, the PCI VGA controller should not respond to the

Write, it should only snoop the data and permit the access to be

forwarded to the ISA bus.  The non-VGA ISA graphi controller

can then snoop the data on the ISA bus.Unless you have the

above situation, you should disable this option.

The choices:  Disabled (default); Enabled

Содержание 4845GVM










































































Отзывы: