background image

DTUS066 rev A1 March 21, 2012 

WLn-LINK-OEM HARDWARE MANUAL 

 

COPYRIGHT (©) ACKSYS 2012 

This document contains information protected by Copyright. 
The  present  document  may  not  be  wholly  or  partially  reproduced, 
transcribed,  stored  in  any  computer  or  other  system  whatsoever,  or 
translated into any language or computer language whatsoever without 
prior  written consent from ACKSYS Communications & Systems  - ZA 
Val  Joyeux 

–  10,  rue  des  Entrepreneurs  -  78450  VILLEPREUX  - 

FRANCE. 
 

REGISTERED TRADEMARKS ® 

  ACKSYS is a registered trademark of ACKSYS. 

 

DISCLAIMERS 

ACKSYS  ®  gives  no  guarantee  as  to  the  content  of  the  present 
document  and  takes  no  responsibility  for  the  profitability  or  the 
suitability of the equipment for the requirements of the user. 

ACKSYS ® will in no case be held responsible for any errors that may 
be  contained  in  this  document,  nor  for  any  damage,  no  matter  how 
substantial,  occasioned  by  the  provision,  operation  or  use  of  the 
equipment. 

ACKSYS  ®  reserves  the  right  to  revise  this  document  periodically  or 
change its contents without notice. 
 

REGULATORY INFORMATION AND DISCLAIMERS 

Installation  and  use  of  this  Wireless  LAN  device  must  be  in  strict 
accordance  with  local  regulation  laws  and  with  the  instructions 
included  in  the  user  documentation  provided  with  the  product.  Any 
changes  or  modifications  (including  the  antennas)  to  this  device  not 
expressly approved by the manufacturer may void the user’s authority 
to operate the equipment. The manufacturer is not responsible for any 
radio or television interference caused by unauthorized modification of 
this device, or the substitution of the connecting cables and equipment 
other than manufacturer specified. It is the responsibility of the user to 
correct  any  interference  caused  by  such  unauthorized  modification, 
substitution or attachment. Manufacturer and any authorized resellers 
or  distributors  will  assume  no  liability  for  any  damage  or  violation  of 
government  regulations  arising  from  failing  to  comply  with  these 
guidelines. 

 

 

10, rue des Entrepreneurs  

 Z.A. Val Joyeux 

78450 VILLEPREUX - France

 

Phone: 

+33 (0)1 30 56 46 46 

Fax: 

+33 (0)1 30 56 12 95 

Web site: 

www.acksys.fr

  

Hotline: 

[email protected]

 

Sales: 

[email protected]

 

Содержание WLn-LINK-OEM-RJ




























Отзывы: