background image

EQUIPMENT DAMAGE HAZARD

Failure  to  follow  this  caution  may  result  in  equipment 

damage. Handle the control with care and avoid getting 

the control wet.

CAUTION

!

IMPORTANT

:  The  remote  control  can  operate  the  unit  from  a 

distance of up to 26 ft. (8 m) as long as there are no obstructions. 
When the timer function is used, the remote control should be kept 
in the vicinity of the fan coil (within 26 ft. / 8 m). The remote 
control can perform the following basic functions:

S

Turn the system 

ON 

and 

OFF

S

Select the operating mode

S

Adjust the room air temperature set point and fan speed

S

Adjust the airflow direction

Refer  to  the 

Remote  Control  Function  section  for  a  detailed 

description of all the capabilities of the remote control.

Battery Installation

Two  AAA  1.5v  alkaline  batteries  (included)  are  required  for 
operation of the remote control.
To install or replace batteries:

1. Slide  the  back  cover  off  the  control  to  open  the  battery

compartment.

2. Insert  batteries.  Follow  the  polarity  markings  inside  the

battery compartment.

3. Replace the battery compartment cover.

NOTE: 

1. When  replacing  batteries,  do  not  use  old  batteries  or  a

different type of battery. This may cause the remote control
to malfunction.

2. If  the  remote  is  not  going  to  be  used  for  several  weeks,

remove  the  batteries.  Otherwise  battery  leakage  may
damage the remote control.

3. The  average  battery  life  under  normal  use  is  about  6

months.

4. Replace the batteries when there is no audible beep from the

indoor unit or if the Transmission Indicator fails to light.

5. When the batteries are removed, the remote control erases

all programmed settings. The control must be
reprogrammed after insertion of the new batteries.

Remote Control Operation − Quick Start

NOTE: 

When transmitting a command from the remote control to 

the unit, be sure to point the control toward the right side of the 
unit. The unit confirms receipt of a command by sounding an 
audible beep.

1.

Turn the unit on by pushing the 

ON/OFF

 button.

2.

If there is a preference for ·C rather than ·F (default), press

and hold the increase 

 and decrease 

 temperature set 

point buttons together for approximately 3 seconds.

3.

Select the desired mode by pushing the mode button.

AUTO

 

COOL

 

DRY

 

HEAT

 

FAN

Fig. 6 − Modes

4. Select  the  temperature  set  point  by  pointing  the  control

toward  the  unit  and  pressing  the  increase/decrease
temperature set point buttons until the desired
temperature appears on screen.

5. Press 

FAN

  to select the desired fan speed.

NOTE: 

If the unit is operating in the 

DRY 

or 

AUTO 

mode, the fan 

speed will be automatically set.

6. Set  the  airflow  direction.  When  the  unit  is  turned  on,  the

louvers  default  to  the  cooling  or  heating  position.  The  user
can  adjust  the  horizontal  louver  position  by  pushing

DIRECT 

or  have  continuous  louver  movement  by  pressing

SWING

.

Manual Operation

If  the  remote  control  is  lost,  damaged,  or  the  batteries  are 
exhausted, the 

MANUAL

 button can be used to run the unit. 

When  the 

MANUAL 

button  is  pressed  once,  the 

AUTO 

mode 

takes affect (heat or cool). When this button is pressed twice, the 
system  enters  the 

TEST 

mode  and  runs  for  30  minutes  in  the 

COOLING 

mode  (it  will  run  in  the 

AUTO 

mode  afterward). 

When pressed three times, the system turns off.

Manual control button

Fig. 7 − Manual Button

The set conditions of manual operation are as follows:

S

Preset set point: 76F (24C)

S

Fan speed: 

AUTO

S

Discharge air direction: Pre−set position based on operation in
the “

COOL

”or “

HEAT

” mode.

IMPORTANT

:  The  manual  button  is  intended  for  testing  purposes 

and emergency operation only. Do not use this function unless the 
remote  controller  is  lost.  To  restore  regular  operation,  use  the 
remote controller to activate the unit.

Page 

1

1

Содержание ACIQ-18FM-HH-MB













































Отзывы: