background image

Automation Components, Inc.

2305 Pleasant View Road  |  Middleton, WI 53562

Phone:

 1-888-967-5224  |  

Website:

 workaci.com

Page 7

Version: 3.0

I0000470

PRODUCT SPECIFICATIONS

WARRANTY

The ARM Series is covered by ACI’s Two (2) Year Limited Warranty, which is located in the front of ACI’S SENSORS & 
TRANSMITTERS CATALOG or can be found on ACI’s website: www.workaci.com.

W.E.E.E. DIRECTIVE

 

At the end of their useful life the packaging and product should be disposed of via a suitable recycling 
centre. Do not dispose of with household waste. Do not burn.

Page 6

24 VAC or 24VDC, (+/- 10%), 50/60 Hz 
200 mA maximum 
0 to 35 VDC @ 1MΩ

0-44 mA @ 250Ω 

0 to 500,000Ω
Multi-turn potentiometers
0.25 VDC minimum to 20 VDC maximum
44 mA maximum, Signal Gain 1 to 25 times (nominal) depending on input value
+/- 1%
0 to 100%
0.25 to 20 VDC
20 to 0.25 VDC (nominal)
750Ω @ 20 mA
3300Ω @ 20 VDC +/- 10% / 400Ω @ 10 VDC +/- 10%
20 VDC +/- 10%, 30 mA maximum
45° Captive screw Terminal Blocks
12 (3.31 mm2) to 22 AWG (0.33 mm2)
0.5 Nm (Minimum); 0.6 Nm (Maximum)
35 to 120°F (1.7 to 48.9°C)
10 to 95% non-condensing 
-20 to 150°F (-28.9 to 65.5°C)
Polyvinyl Chloride (PVC)
UL94 V-0 
RoHS2, WEEE

NON-SPECIFIC INFORMATION

 

Supply Voltage:
Supply Current:
Input Voltage Signal Range (@ 
Impedance):
Input Current Signal Range (@ 
Impedance):
Input Resistance Signal Range:
Field Adjustable Ranges:
Output Voltage Signal Range:
Output Current Signal Range:
Output Accuracy:
Output Signal Attenuation:
Output Signal Offset:
Output Signal Inversion (RA):
Output Current Load Impedance:
Output Voltage Load Impedance:
Regulated Power Output:
Connections:
Wire Size:
Terminal Block Torque Rating:
Operating Temperature Range: 
Operating Humidity Range:
Storage Temperature:
Snaptrack Material:
Snaptrack Flammability Rating:
Agency Approvals:

Содержание ANALOG RESCALING Series









Отзывы: