background image

75

 

 

 

 

 

PREPARATION FOR OPERATION IN 

COLD WEATHER

 

1.

 

Replace engine oil and hydraulic oil with 
those  of  viscosities  suitable  for  cold 
weather.

 

2.

 

In cold weather, battery power drops, and 
the battery fluid may freeze if the battery 
is  not  sufficiently  charged.  To  prevent 
the battery fluid from freezing, be sure 
to keep the battery charged at least 75% 
or more of its capacity after operation. 
To ease next starting, it is recommended 
to  keep  the  battery  stored  in  closed  or 
heated rooms. If the battery fluid level is 
too low, do not add after operation, but 
add  with  the  engine running  before  the 
next operation.

 

3.

 

Add anti-freeze to  coolant  in  the radiator 
and  reserve  tank,  if  the  ambient 
temperature  is  expected  to  drop  below 
0ºC. Mixing ratio of water  and  anti- freeze 
depends  on  the  expected  ambient 
temperature.

 

 

 

Mixing  ratio  between  water  and  anti- 
freeze

 

 

Ambient 

Temperature 

 

–5 

 

–10 

 

–15 

 

–20 

 

–25 

 

–30 

 

–35 

Antifreeze %  30  30  30  35  40  45  50 

Water % 

70  70  70  65  60  55  50 

 

IMPORTANT:

 

 

Use  permanent  anti-freeze  or  longlife 
coolant.

 

 

Drain  the  coolant  completely  and  clean 
inside  of  the  radiator  then  fill  with  the 
water and anti-freeze mixture.

 

 

The anti-freeze acts as an anti-corrosive, 
it is not necessary to add an additive to 
the water and anti-freeze mixture.

 

 

See  “Coolant  check”  under  “DAILY 
CHECKS” 

in 

“MAINTENANCE” 

for 

radiator fill volumes.

 

PROCEDURE AFTER DONE WORK

 

Clean  the  excavator  thoroughly  after  work 
and  wipe  dry.  Otherwise  mud  and  earth  on 
the  tracks  could  freeze  if  the  temperature 
drops below the 0ºC mark. Operation of the 
excavator  is  then  not  possible.  Store  the 
excavator in a dry place; if not possible, store 
on wooden planks or on mats. If the excavator 
is kept on damp or muddy ground, the tracks 
could  freeze  overnight.  Operation  of  the 
excavator is then not possible. Furthermore 
the reduction gear may be damaged.

 

Additionally, the piston rods of the hydraulic 
cylinders  must  be  rubbed  dry.  Otherwise 
severe  damage  could  occur  if  dirty  water 
seeps through the seals.

 

OPERATION UNDER COLD WEATHER CONDITIONS

 

Содержание A23S































































































Отзывы: