Acer e-mill 3VSII Скачать руководство пользователя | Manualshive

Страница: 97 / 203

background image

- 9 6 -

CAUTION

DO NOT SHIFT HI -LO LEVER WHILE THE M OTOR IS

RUNNING.

6-6 Power Feed Engagement Crank(#7)

Engages  power  feed  worm  gear.  When  lever  is  in  right  hand  hole,  power  feed  is
engaged.    To  disengage,  pull  knob  out  and  turn  crank  clockwise  and  move  to
opposite position.

NOTE

Handle must be moved in clockwise direction to engage or

disengage power feed. If handle is moved counter -

clockwise no damage will be done, but nothing will

happen.

CAUTION

POWER FEED GEAR MAY BE ENGAGED WHILE

SPINDLE IS TURNING. HOWEVER, IT SHOULD BE

ENGAGED SLOWLY TO AV OID DAMAGE TO THE

WORM GEAR. THE GEAR MAY BE DISENGAGED AT

ANY TIME. DO NOT USE POWER FEED AT SPEEDS

ABOVE 3000 RPM.

IMPORTANT

IT IS RECOMMENDED TH AT THE POWER FEED

WORM GEAR BE DISENGA GED WHENEVER THE

POWER FEED IS NOT RE QUIRED. THIS WILL AVOID

UNNECESSARY WEAR ON PWER FEED WORM GEAR.

6-7 Quill Feed Selector (#8)

This  crank  is  used  to  select  the  feed  rate.    It  is  shifted  by  pulling  knob  out  and
turning  from  one  position  to  another.    Feed  rates  are  stamped  on  cover  below  each
hole.  Feed is more readily engaged with spindle running.

6-8 Feed Reverse Knob (#10 )

Position of this knob depends upon direction of spindle rotation. If boring with
right hand cutting tools, pull feed handle towards operator until clutch becomes
engaged.

Neutral position is between forward and reverse position. It is recommended that
he handle be left in neutral position when not in use.

6-9 Manual Feed Handwheel (#9 )

Feed reversing knob should be in neutral position and fe ed control lever engaged.
Clock wise rotation of handwheel moves quill down. Manual Feed Handwheel and

«
...
95
96
97
98
99
...
»

Содержание e-mill 3VSII












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-mill 3VSII

Бренд: Gallagher Страницы: 90

Бренд: Gallagher Страницы: 24

Бренд: Paslode Страницы: 20

Бренд: M-system Страницы: 3

Бренд: Ransburg Страницы: 40

Color Block PSU-05B

Бренд: Chroma Страницы: 2

Бренд: Conrad Electronic Страницы: 5

Dr.Peters EPG-5-ULTRA

Бренд: Glomar Страницы: 13

Бренд: YATO Страницы: 112

Бренд: AccuMate Страницы: 12

Бренд: VacuMaid Страницы: 16

Бренд: C-TEC Страницы: 2

Бренд: Kreg Страницы: 36

Бренд: H&S Страницы: 2

Бренд: Parkside Страницы: 109

Бренд: Neilsen Страницы: 8

Бренд: Grizzly Страницы: 8

Бренд: SafeWaze Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды