Acer e-mill 3VSII Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 203

background image

- 9 5 -

6 -2 D r a w B a r

DO NOT attempt to change spindle RPM u nless the motor is running, expressed
speeds will only be approximate. Belt wear will cause variations in speed, from the
speed indicated by the digital counter .

When  tightening  or  loos ening  the  drawbar,   it  is  necessary  to  lock  the  spindle.    To
do  this,  use  the  spindle  brake  (5 )  which  is  loc ated  on  the  left  side   of  the  belt
housing.    Pull  it  down   until  the  spindle   binds.    Make  sure  the  quill  is  raised  all  the
way.

Drawbar has

7

/

1 6 ” - 2 0

right hand thread on model 3VS, 3VSII, 3VK, 3VKH; 5/8” -11

right  hand  thread  on  model  5VK,  6VK,  and  should  be  tightened  with  normal
pressure  using  wrench  furnished  with  machine.    To  loo sen  collet,  back  off  drawbar,
and  i f  collet  does  not  open   immediately ,  please  give  the  top  of  drawbar  a  slight  tap.
The s pindle has non -sticking taper and  the collet should release  easily.

6-3 Spindle Brake (#5 )

Brake  lever  must  be  pull  down  to  stop  spindle   electronically .    When  locking
spindle,  lever  should  be  pull-down.    There  are  no  adjustments  on  brake,  so  it  must
be replaced when worn out.

CAUTION

BE CERTAIN THAT THE SPINDLE BRAKE IS

RELEASED BEFORE STAR TING THE MOTOR. THE

MOTOR CAN BE DAMAGED IF SWITCH IS TURNED

ON WITH BRAKE IN LOC KED POSITION.

6-4 Forward-Reverse S witch (#3)

This  is  the  motor  reversing  switch.    When  the  head  is  in   direct  drive  (High  Range)
the  motor  and  spindle  are  turning  the  same  direction.    When  the  head  is  in  “Back
Gear”  (Low  Range)  the  spindle  runs  backwards  unless  the  motor  direction  is
reversed.

6-5 Hi-Neutral-Lo Lever (#18 on 5HP or #20 on 3HP )

This lever is used to put the head into either direct drive or back gear. Rotate the
spindle by hand to facilitate meshing of clutch or gears.

Neutral can be obtained at mid -way position, and is provided to permit free spindle
rotation for indicating and set -up.

After  an  extended  period  of  use,  the  neutral  position  may  cause  noise  by  allowing
the  clutch  teeth  to  rub  each  other.    This  can  be  corrected  by  loosening  set  screw
(#43, page 111 ) and reversing the position of the detent plate  (#44, page 111 ).

In  high  speed  (Direct  Drive),  the  spindle  is  driven  by  ta pered  clutch  teeth.    If  the
clutch  is  not  meshed  tightly,  clutch  rattle  will  be  heard.    This  can  be  corrected  by
moving  the  detent  plate  upward  as  the  clutch  wears.    This  may  also  cause  loss  of
neutral, requiring reversal of the detent plate.

«
...
94
95
96
97
98
...
»

Содержание e-mill 3VSII












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-mill 3VSII

Бренд: Samoa Страницы: 16

Бренд: Gage Bilt Страницы: 24

STORMFORCE SFAR12

Бренд: Draper Страницы: 22

Бренд: Whelen Engineering Company Страницы: 4

Бренд: Artos Страницы: 185

Бренд: HELVAR Страницы: 2

Бренд: FDT Страницы: 4

Бренд: Protool Страницы: 60

Universal CPU Holder

Бренд: Ergotron Страницы: 14

Бренд: Parkside Страницы: 16

Бренд: Wen Страницы: 2

Бренд: Wido Страницы: 16

Бренд: NENZ Страницы: 24

Бренд: Alpha Страницы: 4

Allen-Bradley ControlLogix 1756-L Series

Бренд: Rockwell Automation Страницы: 307

Бренд: Klein Tools Страницы: 1

Бренд: IAN CANADA Страницы: 15

Бренд: BJLive Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды