Acer Aspire AM5610 Скачать руководство пользователя страница 8

Страница: 8 / 113

Chapter 1

SATA Interface

•

Four slots

•

Compliant to SATA 2.0 specification

•

IDE/ AHCI mode support

•

HDD/ CD-ROM/ CD-RW/ DVD-ROM/ DVD-RW/ DVD+RW/ DVD Dual/ DVD Super Multi Plus support

Audio

•

Realtek HD audio codec ALC888 HD codec 7.1 channels

•

Six audio jack on the rear side of the unit, compliant to Realtek HD audio definition

•

One 2*5 front audio header

•

One S/PDIF-out header (1*4)

•

One AUX-In header

•

S/N ratio: 90 dB for the rear output jack

LAN

•

Marvell 88E8056 PCI-E Gigabit Ethernet controller

USB

•

Five OHCI and one EHCI host controllers to support ten ports

•

Three 2*5 onboard headers

•

Four ports for front daughter board

•

Two ports for internal USB card IR module

•

Compliant to standard Intel FPIO pin definition

•

USB 2.0/1.1 support

1394a

•

Ti TSB43AB23PDTG4 controller

•

One 2*5 onboard header

•

One 6-pin 1394 port on the rear side of the unit

Buzzer

•

One onboard buzzer

Front Panel I/O Header

Содержание Aspire AM5610


















































































































Результаты поиска

Содержание Aspire AM5610

Отзывы:

Похожие инструкции для Aspire AM5610

Бренды по названию

Популярные бренды

Acer Aspire AM5610, Руководство по обслуживанию

Результаты поиска

Содержание Aspire AM5610

Отзывы:

Похожие инструкции для Aspire AM5610

Бренды по названию

Популярные бренды