manualshive.com logo in svg

ACEK9 Hot-N-Pop Pro, Руководство по установке

Поделиться
Скачать
ACEK9 Hot-N-Pop Pro Скачать руководство пользователя страница 10

9

STEP 10 Heat Alarm Ignition Power

Red/Yellow (pin 7)

From the Protective Relay Module connect the

Red/Yellow

Ignition wire to the police package

ignition point, or switched Ignition Power point on the Vehicle’s fuse panel.

Ignition must

be connected for proper operation of K9 Heat Alarm

®

Ignition and Power Warnings

Do not use devices that remove power to vehicle systems, alert features of this
product or emergency warning systems that it activates

.

Alarms, Auto Starters, Antitheft Devices or any systems that shut off ignition
power, The K9 Heat Alarm power MUST be set up as to requite manual shut down

by the person responsible for the K9.

Use settings

“On/Off Manually”

“Car On Manually off”
“No K9 Left Behind”

[if purchased and installed

]

STEP 11 Stall Sensor Option

Sold Separately, required for auto start add on.

The stall sensor makes it easy to detect an engine stall. The sensor detects the energy
emanating from the alternator to determine that the engine is running. Mount the stall

sensor against the metal alternator housing, over visible coils. Use heat rated cable ties or
hardware. Route the stall sensor wire through the firewall to the IntelaBox. If you have to

drill a hole, use the supplied grommet, seal with silicone (not supplied). Cover the stall
sensor cable with heat rated wire loom, avoid contact with moving parts and hot exhaust

parts. (the stall sensor needs to be enabled in the Menu)

VERIFY that the stall sensor functions well after the vehicles battery is fully charged and
under minimal load. Run vehicle.

The LED on the Sensor is lighted red when the vehicle is

stalled or not running.

“Tip”

Idle the vehicle till battery is fully charged,

If the light turns red when the vehicle is running it

may need to be repositioned. Flipping the sensor on its side may improve function.

Step 12 Optional add on modules

Connect any add on accessories purchased with system. See instructions included with
accessory. Do not attempt to connect items not approved for use with this system. See the

Installation Manual(s) for details. Use only accessories designed for Acek9.com products.

Heat Alarm test next page

Содержание Hot-N-Pop Pro




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды