background image

                                                                                                          T-APM - Apex Premier F

UME 

H

OOD 

M

ONITOR 

 

  T-APM                          0133MAN00015 - Rev J                      ECN  -                       JUL 2017                     

Page 27 of 61

 

Configuration of the APM

 

 
Selection 3

: Configure High Voltage Output Level 

[SCREEN 4L]

 

The next item to configure is the required high voltage output from the APM.  This is the highest voltage 
the APM will provide indicating a high face velocity.  For example, if the desired voltage output is 1 to 
5Vdc, indicating 50 to 200FPM the value of 5Vdc would be entered using the plus and minus buttons [ 

 

and 

 ].  Press the 

ACCEPT

 button when the required maximum output voltage is correctly displayed. 

 

Selection 4

: Select Velocity Range 

[SCREEN 2L]

Press the 

VELOCITY RANGE

 button to configure the velocity range for the analog output to follow.   

 

Selection 5

: Configure Low Velocity Level 

[SCREEN 5L]

 

The low velocity selection screen appears and prompts for a low velocity to equate to the previously 
entered low voltage value.  This is the lowest velocity the analog output will respond to.  For example, if 
the desired voltage output is 1 to 5Vdc, indicating 50 to 200FPM, the value of 50FPM would be entered 
using the plus and minus buttons [

 and 

].  Press the 

ACCEPT

 button when the required minimum 

velocity is correctly displayed. 
 

Selection 6

: Configure High Velocity Range 

[SCREEN 6L]

 

The last item to configure is the required high velocity reading to equate to the previously entered high 
voltage selection.   This is the highest velocity the analog output of the APM will respond to.  For 
example, if the desired voltage output is 1 to 5Vdc, indicating 50 to 200FPM the value of 200FPM would 
be entered using the plus and minus buttons [ 

 and 

 ].  Press the 

ACCEPT

 button when the required 

maximum velocity is correctly displayed. 
 

Selection 7

: Final Verification of Settings 

After all the configuration screens have been completed, the resulting setup of the analog output will be 
properly displayed on the main 

ANALOG OUTPUT SCALING SCREEN

 

[SCREEN 2L]

.  Verify all entered values are 

correct, if not re-configure them as stated in the above selections and when all settings are correct, press 
the 

COMPLETE

 button to exit back to the 

MAIN CONFIGURATION MENU

 

Contrast Adjustment 

If desired, the contrast of the display can be adjusted by the 

CONTRAST ADJUST

 configuration menu 

[SCREEN 1M]

.  Press the 

CONTRAST ADJUST

 button on the main configuration menu to enable.  By 

pressing the 

INCREASE

 or 

DECREASE

 buttons, the contrast will be adjusted accordingly.  Note: the 

contrast adjustment buttons are designed to “wrap around” so if the same button is pressed, the contrast 
will be adjusted to the maximum or minimum and then flip back around again.  Also note that if the 
contrast adjustment causes the contrast to change to the point of not being legible, continue to press the 
same place on the display to allow for the adjustment to wrap around and once again become legible. 
 
Press the 

ACCEPT

 button when the best contrast is achieved.  Press the 

CANCEL

 button to cancel out of 

this screen. 

Содержание Apex Premier






























































Отзывы: