Installation & Operation Manual
- Model AVT6000
Page A6
SUBMITTAL DRAWING
THIS DOCUMENT IS SUBJECT
TO CHANGE WITHOUT NOTICE.
THIS DOCUMENT OR THE CONTENTS
THEREOF SHALL NOT BE MODIFIED
WITHOUT PRIOR WRITTEN
PERMISSION BY ACCUTROL LLC.
Actuator, Standard-Speed, FLP, 2-10V
DWG. NO:
REVISION:
SHEET:
OF
ECN:
1
1
REV. DATE:
INSTALLATION
3-10-20
APPLICATION
Accutrol Representative:
The 20-0057 actuator is used for AccuValve
®
applications that require standard-speed response over a control
range of 2 to 10 volts and will
fail in place when power is removed.
DIMENSIONS
1. Slide actuator V-clamp over the AccuValve drive shaft.
2. Align the flat of the drive shaft with the flat of the shaft
coupling.
3. Slide the slot on the back of the actuator over the vertical
tab on the anti-rotation bracket so the tab is captured in the
slot.
4. Secure the actuator coupling to the AccuValve drive shaft
by tightening the (2) 10mm nuts on the v-clamp. Secure
each nut evenly and torque each nut to 6 to 7 ft-lbs.
TECHNICAL DATA
Each actuator is installed, configured and tested on the AccuValve
®
prior to shipping from the Accutrol factory.
The following instructions are provided as a reference for replacing an actuator in the field.
21 COMMERCE DRIVE
DANBURY, CT, 06810
Tel: 203-445-9991
Accutrolllc.com
2597
A
20-0057 SUBMITTAL DWG
Parts Required
(1) Actuator, PN 20-0057
(2) Screws, PN 17-0246 (#8-32 x 5/16)
Tools Required
10mm wrench
#2 Phillips Head Screw Driver
ELECTRICAL
Power Supply
24 VAC +/- 20% 50/60 Hz, or 24 VDC +/- 10%
Power Consumption:
1.4 W nominal, 4.0 W max
Transformer Sizing:
6 VA (Class 2 power source)
Electrical Connection:
Cable, 3’ Plenum, NEMA 2 (IP 54), 4-Conductor, 18 GA
Overload Protection:
Electronic, throughout range of rotation
Control Signal:
2 to 10V
Feedback Signal:
2 to 10V
Input Impedance:
Resolution:
100K ohm
45mV response to control signal
89mV response to control signal change of direction
MECHANICAL
Angle of Rotation:
Factory-set with mechanical stops (approximately 45°)
Running Time:
22 seconds full stroke
Torque:
90 in-lb (10Nm)
Direction of Rotation:
Reversible with switch
Manual Override:
External push button
Weight:
2.2 lbs. (1.0 kg)
Noise Level:
< 45 dBA
Housing Material:
UL94-5VA
ENVIRONMENTAL
Humidity:
5 to 95% RH non-condensing (EN 60730)
Operating Temperature: -22°F to 122°F (-30°C to 50°C)
Storage Temperature:
-40°F to 176°F (-40°C to 80°C)
Housing:
NEMA 2, IP54, UL enclosure type 2
AGENCY LISTINGS & QUALITY STANDARDS
cULus acc. to UL 60730-1A/-2-14
CAN/CSA E60730-1:02
CE acc. to 2014/30/EU and 2014/35/EU
QS ISO 9001
SERVICE
No Maintenance Required
WIRING
Reference Figure 2
Rotation
Direction
Switch
V-Clamp
Drive Shaft
Coupling
Mechanical
Stops
Clutch
Drive
Shaft
Mounting Bracket
Figure 2
Figure 3
Anti-Rotation
Bracket
500
Ω resistor is required only
when using current control signal.
Adaption
3.90"[99]
4.76"[121]
7.76"[197]
2.
44
"[
62
]
24 VAC Class 2 Transformer or 24 VDC
