manualshive.com logo in svg

AccuStream AccuValve On/Off Valve, Руководство пользователя

Поделиться
Скачать
AccuStream AccuValve On/Off Valve Скачать руководство пользователя страница 7

AccuStream Cutting Systems 

  

5 

13084 ON/OFF VALVE & CUTTING HEAD MANUAL 

4

 

AccuValve On/Off Valve 

The 

Accustream On/Off Valve

 (AccuValve) is an ultra high-pressure valve used to control the flow of 

water for waterjet cutting applications. 

The On/Off valve is a normally closed (air to open, spring closed) valve that can be direct mounted to 
the cutting head for water or abrasivejet cutting see Mounting Collar (below), or it can be remote 
mounted with separate plumbing from the valve to the cutting head.  The valve can also be remotely 
mounted on the cutting head. 

4.1

 

Specifications 

Fluid pressure 

Operating pressure 

60,000 psi water max 

Actuator Air Pressure 

60-80 psi to open 

Weight 

Valve Only 

2.5 pounds 

Valve w/Mntg Collar and Abrasive Head 

5.5 pounds 

Size 

Valve Only 

3.1” dia x 5” 

Valve with Abrasive Head 

3.1” dia x 11.6” 

 

Содержание AccuValve On/Off Valve





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды