AccuAir ENDO-CVT Series Скачать руководство пользователя страница 9

Страница: 9 / 20

Page 6

ENDO-CVT Instructions V1.

AccuAir Suspension 2018

Comp Trigger IN

<12V Digital IN>

Tank Pressure OUT

<0.5-4.5V DAC>

Replace with Comp Trigger IN

Adapter Harness Yellow Wire

Plug Terminals #6 and #13

Replace with Tank Pressure OUT

Adapter Harness Green Wire

(8) UP/DN

1/2/3/4

<12V Digital IN>

12 in

M8 to CVT Connector

STATUS INDICATOR

LIGHT

Re-Pin Into e-Level Main Harness Connector

RE-PINNING E-LEVEL

MAIN HARNESS CONNECTOR

CVT ADAPTER HARNESS

T_W
1_Black to Eye-Let EC_GND

6_Red (P-SENS) PLUG

7_Green (Tank Pressure)

8_Purple HEADLIGHTS

10_

11_

12_Yellow to COMP Trigger IN

13_Black (P-SENS) PLUG

14_Orange IGN_12V

15_

16_Red to 10 Amp Fuse

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

REMOVING & REPLACING AN MX150 WIRE

T= Terminal W= Wire

1.) Up 4

White/Black

2.) Up 3

White/Orange

3.) Up 2

White/Purple

4.) Up 1

White

5.) Down 4 White/Gray

6.) Down 3 White/Green

7.) Down 2 White/Brown

8.) Down 1 White/Blue

8-Pin ADAPTER HARNESS

NOTE:

This harness can be re-oriented for non standard CVT vehicle orientations.

STEP #1

STEP #2

STEP #3

STEP #4

STEP #5

STEP #9

STEP #6

STEP #7

STEP #8

STEP #10

STEP #11

BACK OF CONNECTOR

Figure 4:

CVT Adapter harness

Figure 5:

Re-pinning e-Level™ main harness connector

Figure 6:

Removing & replacing an MX150 wire

Содержание ENDO-CVT Series





















Результаты поиска

Содержание ENDO-CVT Series

Отзывы:

Бренды по названию

Популярные бренды

AccuAir ENDO-CVT Series, Инструкция по эксплуатации

Результаты поиска

Содержание ENDO-CVT Series

Отзывы:

Бренды по названию

Популярные бренды