Accu-Scope EXM-150-MS Скачать руководство пользователя страница 12

Страница: 12 / 14

EXM-150 MICROSCOPE SERIES

ACCU-SCOPE

IMAGE PROBLEMS

Problem

Cause

Corrective Measures

Image moves while focusing

Specimen rises from stage
surface

Revolving nosepiece is not in
the click-stop position

Secure the specimen in the
slide holder

Revolve the nosepiece to the
click-stop position

Image tinged yellow

Lamp intensity is too low

Blue filter not used

Adjust the light intensity by
rotating the intensity control
dial and/or iris diaphragm

Use daylight blue filter

Image is too bright

Lamp intensity is too high

Adjust the light intensity by
rotating the intensity control
dial and/or iris diaphragm

Insufficient brightness

Lamp intensity is too low

Aperture diaphragm closed too
far

Condenser position too low

Adjust the light intensity by
rotating the intensity control
dial and/or iris diaphragm

Open to the proper setting

Position the condenser slightly
lower than the upper limit

MECHANICAL PROBLEMS

Image will not focus with high
power objectives

Slide upside down

Cover glass is to thick

Turn the slide over so the
cover glass faces up

Use a 0.17mm cover glass

High power objective contacts
slide when changed from low
power objective

Slide upside down

Cover glass is to thick

Diopter adjustment is not set
properly

Turn the slide over so the
cover glass faces up

Use a 0.17mm cover glass

Readjust the diopter settings
as outlined in section 4.3

Содержание EXM-150-MS















Результаты поиска

Содержание EXM-150-MS

Отзывы:

Похожие инструкции для EXM-150-MS

Бренды по названию

Популярные бренды

Accu-Scope EXM-150-MS, Руководство пользователя

Результаты поиска

Содержание EXM-150-MS

Отзывы:

Похожие инструкции для EXM-150-MS

Бренды по названию

Популярные бренды