background image

EXC-100 MICROSCOPE SERIES 

 

73 Mall Drive, Commack, NY 11725 • 631

-864-

1000 • 

www.accu-scope.com 

11 

 

ADJUSTMENT & OPERATION

 (continued)

 

 

 

Fig. 11 

 

Adjusting the Condenser (Aperture Diaphragm) 

1.  The aperture diaphragm determines the Numerical Aperture (N.A.) of 

the illumination system. When the N.A. of illumination system matches 

the N.A. of the objective, resolution and contrast are optimized. The 

aperture diaphragm can also increase the depth of field by closing it 

down from the optimal position (resolution is sacrificed by doing this). 

2.  Turn the condenser lever right or left to change the height of the 

condenser and the N.A. of the illumination system (see Fig. 11).    The 

condenser should be in its highest position during operation. 

3.  Move the aperture diaphragm lever to the value that is close to the 

magnification of the objective (e.g., 10 for the 10x objective).    Repeat 

for each time a different objective is rotated into the light path. 

 

Fig. 12 

Using the 100x Oil Immersion Objective 

1.  Use the 4X objective to focus the specimen. 

2.  Place a drop of oil

 on the specimen observed (see Fig. 

12) 

3.  Rotate the nosepiece counterclockwise and rotate the oil 

objective (100X) into the light path. Then use the fine 

focusing knob to focus. 

 

Make sure there is no air bubble in the oil.   

A. Move the eyepiece to examine the air bubble. Open the 

aperture diaphragm and field diaphragm fully and observe the 

edge of the objective from the tube (It seems round and 

bright). 

B. Rotate nosepiece slightly and swing the oil objective for 

some times to remove the air bubble.   

4.  After using, wipe the front lens of the objective with a 

tissue moistened with a small amount of 3:7 mixture of 

alcohol and ether or with dimethylbenzene. Wipe off the oil 

on the specimen (cover glass). 

 

DO NOT change objectives in the light path before the oil is 
wiped off from the slide to avoid getting oil on a non-oil 

objective and causing damage to it. 

 

Be careful not to use too much solvent to clean the lens as 
this may also damage the lens in the long term. 

 

Содержание EXC-100 Series




















Отзывы: