background image

3000-LED MICROSCOPE SERIES 

ACCU-SCOPE

®

20

 

MAINTENANCE 

Please remember to 

never 

leave the microscope with any of the objectives or eyepieces removed and 

always protect the microscope with the dust cover when not in use. 

SERVICE 

ACCU-SCOPE

 ®

 microscopes are precision instruments which require periodic servicing to keep them 

performing properly and to compensate for normal wear. A regular schedule of preventative maintenance 
by qualified personnel is highly recommended. Your authorized ACCU-SCOPE

 ®

 distributor can arrange 

for this service. Should unexpected problems be experienced with your instrument, proceed as follows: 

1. Contact the ACCU-SCOPE

 ®

 distributor from whom you purchased the microscope. Some

problems can be resolved simply over the telephone.

2. If it is determined that the microscope should be returned to your ACCU-SCOPE

 ®

 distributor or to

ACCU-SCOPE

 ®

 for warranty repair, pack the instrument in its original Styrofoam shipping carton. If you

no longer have this carton, pack the microscope in a crush-resistant carton with a minimum of three
inches of a shock absorbing material surrounding it to prevent in-transit damage. The microscope should
be wrapped in a plastic bag to prevent Styrofoam dust from damaging the microscope. Always ship the
microscope in an upright position; 

NEVER SHIP A MICROSCOPE ON ITS SIDE

. The microscope or

component should be shipped prepaid and insured.

LIMITED MICROSCOPE WARRANTY

 

This microscope and its electronic components are warranted to be free from defects in material and workmanship 
for a period of five years from the date of invoice to the original (end user) purchaser.  The LED lamp is warranted 
for a period of two years from the date of invoice to the original (end user) purchaser.  This warranty does not cover 
damage caused in-transit, misuse, neglect, abuse or damage resulting from improper servicing or modification by 
other then ACCU-SCOPE approved service personnel.  This warranty does not cover any routine maintenance 
work or any other work, which is reasonably expected to be performed by the purchaser. Normal wear is excluded 
from this warranty. No responsibility is assumed for unsatisfactory operating performance due to environmental 
conditions such as humidity, dust, corrosive chemicals, deposition of oil or other foreign matter, spillage or other 
conditions beyond the control of ACCU-SCOPE INC.  This warranty expressly excludes any liability by ACCU-
SCOPE INC. for consequential loss or damage on any grounds, such as (but not limited to) the non-availability to 
the End User of the product(s) under warranty or the need to repair work processes.  Should any defect in material, 
workmanship or electronic component occur under this warranty contact your ACCU-SCOPE distributor or ACCU-
SCOPE at (631) 864-1000.  This warranty is limited to the continental United States of America.  All items returned 
for warranty repair must be sent freight prepaid and insured to ACCU-SCOPE INC., 73 Mall Drive, Commack, NY 
11725 – USA.  All warranty repairs will be returned freight prepaid to any destination within the continental United 
States of America, for all foreign warranty repairs return freight charges are the responsibility of the 
individual/company who returned the merchandise for repair.  

ACCU-SCOPE is a registered trademark of ACCU-SCOPE INC., Commack, NY 11725 

Содержание 3000-LED-SPH





















Отзывы: