manualshive.com logo in svg

Acces I/O products PCI-ICM-2S, Руководство пользователя

Поделиться
Скачать
Acces I/O products PCI-ICM-2S Скачать руководство пользователя страница 11

Chapter 3: Option Selection

  
Operation of the serial communications section is determined by jumper installation as described 
in the following paragraphs. Locations of the jumpers are shown in Figure 3-1, Option Selection at 
the end of this section of the manual. 

  

422/485

 

Jumpers must be installed in these blocks for each COM port. The function of the 422 and 485 
jumpers is to configure the port for RS-422 or RS-485 mode communications. Either an RS-422 
or RS-485 jumper must be used for each channel. 

  

Terminations and Bias

 

A transmission line should be terminated at the receiving end in its characteristic impedance. 
Installing a jumper at the location labeled LDO applies a 120

Ω

 load across the output for RS-422 

mode and across the transmit/receive input/output for RS-485 operation. 
  
Installing a jumper at the location labeled LDI applies a 120

Ω

 load across the input for RS-422 

operation. 
  
The card provides biasing for the RS-485 mode. This biasing is capacitively coupled and is 
present on all boards. 

  

CLK X1 and CLK X4

 

Placement of this jumper controls baud rate. CLK X1 permits baud rates up to 115.2K Baud and 
CLK X4 permits baud rates up to 460.8K Baud. 

  

 

Data Cable Wiring

 

When two numbers are joined together with a "&" the two pins are jumpered together. 
 

 Cable 
Mode 

 

Jumpers 

Card 1 

Card 2 

Simplex 

2-wire Receive Only  422 

Rx+ 9 

2 

  

 

Rx- 

1 

3 

 
Simplex 

2-wire Transmit Only 422 

Tx+ 2 

9 

  

 

Tx- 

3 

1 

 
Half-Duplex 2-wire 

485 

TRx+ 

2 

2 

  

 

TRx- 

3 

3 

 
Full Duplex 

4-wire 

422 

Tx+ 2 

9 

  

 

Tx- 

3 

1 

  

 

Rx+ 

9 

2 

  

 

Rx- 

1 

3 

 

 
  
 

Manual PCI-ICM-2S 

10

Содержание PCI-ICM-2S
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды