Page 6
Page 3
TWO-CAR OPERATION
If two vehicles are equipped with AS635/805
systems, for convenience, both can be operated using the
same remote transmitter. If all four transmitters are to be used with both cars, program transmitters A and
B into the first vehicle in the manner described above. Program transmitters C and D by pressing the Shift
button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second vehicle as
normal, then program transmitters A and B by pressing the Shift button twice before performing steps 3
and 4 above.
When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing
the Shift button twice and the desired function button.
BATTERY REPLACEMENT
Your
AS635/805
Remote Transmitter uses a 12 volt alkaline battery (type 23A), which will require
replacement in time. Depending on the amount of use, the battery may last up to six months or more
before it needs replacement. When the battery needs replacing, the system’s operating range will decrease
or the transmitter LED may not be as bright. In order to change the battery, first remove 2 screws from the
back of the transmitter and separate the top and bottom halves of the case. While replacing the battery
make sure that the positive and negative terminals are positioned correctly, then carefully reassemble the
transmitter case.
2- WAY LCD REMOTE TRANSMITTER DESCRIPTION
Button 1
Arms and disarms the system and when held for 2 seconds, activates the system’s panic
feature.
Button 1 also locks/unlocks the doors when the system is in valet mode.
Button 2
Activates the remote start feature.
Button 3
Activates the auxiliary 1 output normally used for trunk release (note trunk icon on button).
Button 4
Activates the auxiliary 2 output this output will remain on for as long as the button is pressed.
Button 5
Is the confirmation and programming button, quickly pressing button 5 will activate the LCD
display’s backlighting for use in the dark. Pressing button 5 for 2 seconds activates the system’s
confirmation feature which will then display the current status of the system (armed, disarmed,
engine running, etc.).
ADDING/REPLACING 2-WAY LCD TRANSMITTERS
When adding a 2-way LCD transmitter to the system, follow these steps:
1. Turn on the ignition key ON, Off, On, Off, On, Off, and back On. (Key On 4 times)
• The siren will chirp 4 times.
2. Press and hold the override switch for 5 seconds.
• The siren will chirp 4 times.
• The Led will illuminate.
3. Press Button 1 on the first transmitter.
• The siren will chirp once.
4. Turn off the ignition key.
5. Repeat steps 1-4 to add an additional 2-way transmitter.
LCD TRANSMITTER BATTERY REPLACEMENT
Your
AS635/805
transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time.
Depending on the amount of use, the battery may last up to six months before it needs replacement. When
the battery needs replacing, the system’s operating range will decrease, the LCD display will show only one
of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery
voltage drops below minimum. In order to change the battery, first slide the battery door locking pin to the
side. Carefully slide the battery cover downward until it is free. While replacing the battery make sure that
the positive and negative terminals are positioned correctly, then carefully reassemble the transmitter case.
In House/Instructions/Manuals/AS635/805 Owner’s Manual.cdr
The Automatic Rearming feature is designed to protect the vehicle in the event the system is accidentally disarmed. With the
Automatic Rearming feature enabled, the alarm will automatically re-arm 30 seconds after disarming. If the optional Passive Door
Locking feature is enabled, the doors will also lock when the system re-arms.
The Automatic Re-Arming feature will be temporarily bypassed until the next arming cycle if the ignition is turned on or
the trunk/hood zone is opened.
To Remote Start the System
1. Be sure the system is not in Valet Mode.
2. Press and hold Button 4 for three seconds.
• The parking lights will turn on.
• The LED will flash rapidly
• The engine will start and run for the duration of its programmed run time.*
• The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).
*If the engine fails to start on the first attempt, it will repeat the starting procedure 2 more times. If the vehicle fails to start
after a total of 3 times the parking lights will flash 4 times and the doors will lock (if installed).
AUTOMATIC REARMING
REMOTE STARTING
SHUT DOWN
QUICK STOP
The Valet Mode temporarily disables the security system so the vehicle may be operated by a mechanic or parking attendant.
To activate or deactivate the Valet Mode:
VALET MODE
1. Turn on the ignition.
2. Press and hold the override switch for 5 seconds.
• The siren will chirp once to confirm the Valet Mode is on.
• The siren will chirp twice to confirm the Valet Mode is off.
3. Turn off the ignition.
While in Valet Mode the remote transmitters will continue to lock and unlock the doors, and operate the optional auxiliary functions.
Turn on the ignition and press the brake pedal to disengage the remote start feature and drive the vehicle.
When the remote start feature is active, any of the following actions will shutdown the engine.
The quick stop feature allows you exit the vehicle while keeping the engine running for quick stops.
To leave the vehicle running.
1. With engine running press remote start button on your transmitter, sidelights will flash twice indicating quick
stop mode enabled.
2. Turn off the ignition switch, the engine will continue running.
3. You may now exit the vehicle and lock the doors manually or using the remote transmitter.
To resume control of the vehicle.
1. Unlock the doors manually or by pressing Button 4 on the remote transmitter*.
2. Turn on the ignition.
3. Press the brake pedal to disengaged the remote start.
• The LED will turn off.
*If optional keyless entry feature is installed.
1. Pressing Button 4.
• After the engine shuts down the doors will lock (if installed).
2. Pressing the brake pedal.
3. Opening the hood.
4. Remote start time-out (completion of the timed run cycle).
REMOTE START FEATURES
