manualshive.com logo in svg

AC&NC JetStor SAS 780JH JBOD Subsystem, Руководство пользователя

Поделиться
Скачать
AC&NC JetStor SAS 780JH JBOD Subsystem Скачать руководство пользователя страница 51

80 Bays SAS to SAS/SATA  JBOD Subsystem

 

 

User Manual 

51

 

 

NOTE: After replacing the Power Supply Fan Module and turning on 
the Power On/Off Switch of the PSFM, the Power Supply will not 
power on immediately. The Fans in the PSFM will spin-up until the 
RPM becomes stable. When Fan RPM is already stable, the JBOD 
controller will then power on the Power Supply. This process takes 
more or less 30 seconds. This safety measure helps prevent possible 
Power Supply overheating when the Fans cannot work.

 

 

 
 

Appendix A   Zoning Configurations 

 

 

The JBOD subsystem features provide for zoning on the JBOD Controller Modules. This 
allows the input ports on the JBOD Controller Modules to be assigned specifically to 

particular drives in the subsystem. 
 

The JBOD subsystem supports four different zoning modes: Zoning mode 0, Zoning 
mode 1, Zoning mode 2 and Zoning mode 3. 

 

A.1   Zoning mode 0:  Default No Zoning 

 

In this mode, all installed drives are available to all of the host ports on both JBOD 
Controller Modules. 
 

 

 

Steps: 

 

1.

 

Used RS-232 Port (Phone jack to DB9) link SAS JBOD. 

2.

 

In command line please type “phyzone off”, than press “Enter”. 

 

 
 
 
 

 

Содержание JetStor SAS 780JH JBOD Subsystem























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды