Acadia Hearth AH2613i Скачать руководство пользователя страница 19

19

GAS LINE CONNECTION

Gas Conversion (sold separately)

The conversion shall be carried out in accordance with the requirements of the provincial authorities 

having jurisdiction and in accordance with the requirements of the ANSI Z223.1 installation code.

IMPORTANT

This fireplace is manufactured for use with natural gas. Follow the instructions included with the conversion kit if converting to 

LP gas.

Gas Line Installation

 The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any 

pressure testing of that system at pressures in excess of 1/2 psi (3.5 kPa). For test pressures equal to or less than 1/2 

psi (3.5 kPa), the appliance must be isolated from the gas supply piping system by closing its individual manual 

shut-off valve.

Installation of the gas line must only be done by a qualified person in accordance with local 

building codes, if any. If not, follow ANSI 223.1. Commonwealth of Massachusetts installations 

must be done by a licensed plumber or gas fitter.

A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) tee handle manual shut-off valve and flexible gas 

connector are to be connected to the 1/2 in. (13 mm) control valve inlet. If substituting for these components, please consult 

local codes for compliance.
•  If installing this insert into minimum opening dimensions, the gas line may need to be run after placement due to space 

limitations (see the Existing Fireplace Opening Minimum Requirements section of this manual).

• 

This fireplace is equipped with a 3/8” (10 mm) x 18” (457 mm) long flexible gas connector and manual shut-off valve.

• 

Run gas line into fireplace, preferably through left or right gas line holes provided. The gas line should be run to the point 

of connection where the shut-off valve and flexible gas line will connect.

•  Do not run gas line in a manner that would obstruct fan operation.
•  For high altitude installations, consult the local gas distributor or the authority having jurisdiction for proper rating methods.

Inlet Gas Supply Pressures

Fuel

Minimum Pressure

Maximum Pressure

Natural Gas

5” WC (1.25 kPa)

10.5” WC (2.62 kPa)

LP Gas

12” WC (2.99 kPa)

14” WC (3.48 kPa)

INSTALLATION

FACING AND FINISHING

12” 

(305mm)

30”

(762mm)

10”

(254mm)

COMBUSTIBLE 

MANTEL

COMBUSTIBLE

MATERIAL

9” (229mm) CLEARANCE 

TO ADJACENT SIDEWALL

Mantel Requirements

Clearances to Combustibles

Содержание Hearth AH2613i

















































































Отзывы: