background image

 

Page 5 of 40

 

 

 

 

Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall 
onto a hard surface can result in serious injury or death to the user. 

The following is a list of recommended 

ground covers from the Consumer Product Safety Commission:

 

SUGGESTED MATERIAL          UNCOMPRESSED DEPTH

 

Double Shredded Bark Mulch                                9”

 

Uniform Wood Chips 

12”

 

Fine Gravel 

12”

 

Fine Sand 

12”

 

 

The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommend to install 
and  maintain  the  playground  equipment  over  at  least  9  inches  of  wood  chips,  mulch  or  shredded  rubber  (for 
equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock absorbing 
material.  Dirt  and  grass,  which  are  the  most  prevalent  surfaces  under  home  playground  equipment,  do  not 
adequately protect children from serious head injuries. Install protective surfacing at least six feet in all directions 
from play equipment. For swings, the surface should extend, in back and front, twice the height of the suspending 
bar. You should consult a local contractor about ways to secure the product in your location. Do not install your play 
set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. Please refer to the   CONSUMER   
PRODUCT   SAFETY   COMMISSION’S   OUTDOOR   HOME   PLAYGROUND SAFETY

 

HANDBOOK for detailed guidelines to prevent injuries from falls and other hazards on public and home 
playgrounds.

 

 

WARNINGS ON ANCHORING

 

It is highly recommended the product be anchored into the ground to prevent movement and to make the swing 
set more stable during use.

 

 

Some consumers want an anchoring system that allows the product to be moved to different locations. Other 
consumers want to keep their swing set in a permanent location.

 

 

There are different types and different methods of anchoring this product. Sportspower does not make a 
specific anchoring recommendation as each consumers need and conditions can vary.

 

 

It is highly recommended that you seek the opinion from a local licensed contractor on the best way to secure 
the swing set in your location. The best way to anchor a product is to create a concrete footing and use that as a 
base for an anchor. Whatever method you prefer for your location, an anchoring system for this product should 
be used at all times.

 

 

WEATHER CONDITIONS

 

DO NOT use this equipment if the swing seat, slide or any parts are wet. Use the play set only when the parts are 

clean and dry. If the equipment is wet, the user could slip and suffer injuries.

 

Please be aware of weather conditions when using the equipment. If it is too windy, users could lose control and 

suffer injuries. The playground equipment must be properly anchored, stored away or restricted from use during 
inclement  weather such as heavy winds or severe weather storms. You should consult a local  contractor  about 
ways to anchor the product in your location.

 

 

PLAY SUPERVISION

 

DO NOT allow more than one child to play on the individual swing or slide component at any one time. The 

maximum user limit for the flying saucer and glide ride is two persons.

 

DO NOT allow children to stand on the slide, swing seats, flying saucer or glide ride.

 

DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to avoid being 

struck by other children while playing on swings, slides, trampolines etc.

 

 

 

 

 

Содержание MSC-5576













































Отзывы: