background image

 

17 

English 

 

3.4.  Overview configuration parameters 

Z-Wave products can be used directly after inclusion in the network. However, configuration settings 
can be used to adapt the behavior of the device even better to the requirements of the application and 
to activate additional functions. 

Para-

meter 

Byte 

size 

Function 

Default value 

(default) 

Description 

10 

Threshold value 

battery alarm 

10 

Percentage value from when the low battery 
alarm should be transmitted. 

 

Adjustable from 

5 - 50 

in percent 

(Hexadecimal: 0x05 - 0x32) 

14 

BASIC SET to 

association 

group 2 (motion 

alarm) 

BASIC SET should be sent after a motion 
alarm. 

 

0 = Disabled 

 

1 = Active 

(Hexadecimal: 0x00 - 0x01) 

15 

Invert value of 

BASIC SET 

command  

Set the value of the BASIC SET command for 
movement alarm and acknowledgement. 

 

0 = The motion alarm sends the BASIC 
SET value "On" (0xFF), the 
acknowledgement sends the BASIC SET 
value "Off" (0x00) 

 

1 = The motion alarm sends the BASIC 
SET value "Off" (0x00), the 
acknowledgement sends the BASIC SET 
value "On" (0xFF) 

(Hexadecimal: 0x00 - 0x01) 

32 

Bypass function 

Enables or disables the bypass function. 

 

0 = Bypass function activated 

 

1 = Bypass function deactivated 

 (Hexadecimal: 0x00 - 0x01) 

 

 

 

Содержание Nexello PLMK10100




















Отзывы: