background image

Absco Industries

Assembly Instruction Manual

ABSCO PREMIER SHED

MODEL: 30232GECOK

3.00mW x 2.26mD x 2.10mH

Model: 30232GECOK

1.22

24  

 

 

25/11/2021

Australia Product Warranty Against Defects

•  Absco Sheds, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports 

are made using high quality Australian made steel.

•  We are pleased to advise we warrant that the steel coating will not rust, crack, fl ake peel or blister for 

20 

years

 from date of purchase, when installed within Australia.

•  This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of 

steel debris left from cutting, grinding or drilling operations) that has not been removed after building 
construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances. 

•  This warranty covers any Absco product used for normal domestic use and installed in accordance with the 

installation instructions. 

•  The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations. 

•  This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly 

corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or sliding 
padbolts).

•  The warranty is limited to replacement and delivery of components and does not include any labour or 

installation costs. The benefi ts given by the warranty are in addition to your other rights and remedies 
under a law in relation to the goods or services to which the warranty relates.

•  The warranty applies to the exclusion of all other representations, guarantees or warranties express or 

implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and 
is not transferable. You are entitled to a replacement or refund for a major failure and for compensation 
for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if 
the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further 
information go to http://www.consumerlaw.gov.au

•  Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of 

purchase here: http://abscosheds.com.au/warranty-details/

•  In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details 

of the defect, including component part numbers, together with proof of purchase documentation (or 
on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim, 
the Customer Service Manager will contact you within three business days to advise you of the assessment 
outcome of the claim, which may include your expenses incurred in making the claim.

THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110

PHONE

: 1800 029 701 

FAX

: 07 3344 1191 

EMAIL

: [email protected]

Issued 01 January 2018

Содержание PREMIER 30232GECOK


























Отзывы: