ABSCO SHEDS 45232HK страница 2 Скачать руководство пользователя

Страница: 2 / 43

Absco Industries

Assembly Instruction Manual

ABSCO HIGHLANDER SHED

MODEL: 45232HK

4.48mW x 2.26mD x 2.25mH

Model: 45232HK

03/09/2018

1.2

GENERAL INSTRUCTIONS

• Before commencing any assembly, read through these instructions in detail to gain a thorough

understanding of assembly methods and associated details.

• Unpack the carton and carefully identify and check off all the parts against the parts described

and illustrated on "COMPONENTS PACKING LIST" pages.

• Local authority approval must be obtained prior to construction of the shed. Once you have

selected your site you will need to lodge a site plan to your local council.

SITE PREPARATION

• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately

illustrated on “FINAL CONSTRUCTION” page.

If using a rebated slab ensure that all frame

uprights are trimmed 25mm.

TOOLS REQUIRED

SAFETY NOTES

• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and

safety glasses if drilling holes. Sensible shoes are highly recommended.

• Do not erect your shed in windy conditions.
• It is highly recommended to erect the shed with two or more people.

RECOMMENDED

3mm drill bit

10mm drill bits

metal & masonry

Содержание 45232HK












































Результаты поиска

Содержание 45232HK

Отзывы:

Похожие инструкции для 45232HK

Бренды по названию

Популярные бренды

ABSCO SHEDS 45232HK, Руководство пользователя

Результаты поиска

Содержание 45232HK

Отзывы:

Похожие инструкции для 45232HK

Бренды по названию

Популярные бренды