ABSCO SHEDS 15141RK Скачать руководство пользователя страница 1

Страница: 1 / 20

Absco Industries

Assembly Instruction Manual

Model: CYC15

02/03/2021

1.0

N3/C1 FRAME KIT

FOR 1.5m WIDE TO
1.5m DEEP MODELS

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit

www.abscosheds.com.au/review

AU: 1800 029 701

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

This kit is applicable to the following sheds:

The addition of this frame kit will increase the
wind rating of the specified sheds to

Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions

15151GK
15151SK
15141RK

WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.

WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.

Where information conflicts with the original
non-cyclonic instruction manual, this
document is to be referenced.

View of frame kit

applied to

15151GK

Содержание 15141RK





















Результаты поиска

Содержание 15141RK

Отзывы:

Похожие инструкции для 15141RK

Бренды по названию

Популярные бренды

ABSCO SHEDS 15141RK, Руководство по сборке и инструкция

Результаты поиска

Содержание 15141RK

Отзывы:

Похожие инструкции для 15141RK

Бренды по названию

Популярные бренды