manualshive.com logo in svg
background image

 

 Part number 20079, Rev 0 

19 

 

HORIZON SCIENTIFIC, INC. PRODUCT WARRANTY 

Horizon Scientific, Inc. warrants to the original purchaser every new Horizon Scientific, Inc. refrigerated 

unit, the cabinet and all parts thereof, to be free from defects in material or workmanship, when such 

unit is installed, used, and maintained in accordance with provided instructions, for a period of two (2) 

years.  The warranty period starts two weeks from the date of shipment from Horizon Scientific, Inc.  

This  two week period allows ample shipping time so that the warranty will go into effect at 

approximately the same time your equipment is delivered.  Unless subject to prior written agreement 

with

 

Horizon Scientific, Inc., this warranty does not allow for any warranty start deferment greater than 

two weeks from date of shipment due to a delayed installation and/or start-up.  By purchasing any 

product from Horizon Scientific, Inc., you and any entity for which you are purchasing acknowledge and 

agree to each and  every provision contained herein, and all other Notices and Terms provided to 

Purchaser by Horizon Scientific, Inc., which are hereby incorporated. 

Under this warranty, Horizon Scientific, Inc., through its authorized service organizations, will repair, or 

at its option, replace any part found to contain a manufacturing defect in material or workmanship 

without charge to the owner for parts and service labor. Replacement or repaired parts will be 

warranted for only the unexpired portion of the original warranty. Horizon Scientific, Inc. will not 

assume any shipping or cartage costs for parts under warranty. These costs shall be paid by the 

customer. 

ADDITIONAL THREE YEAR COMPRESSOR WARRANTY 

In addition to the two (2) year warranty stated above, Horizon Scientific, Inc. warrants its hermetically 

and semi-hermetically sealed compressors to be free from defects in both material and workmanship 

under normal use and service for a period of three (3) additional years from the end of the initial two (2) 

year warranty period, but not to exceed five (5) years after shipment from Horizon Scientific, Inc. 

Compressors determined by Horizon Scientific, Inc. to have been defective within this extended time 

period will, at Horizon Scientific, Inc.

'

s  option, be either repaired or replaced with a compressor or 

compressor parts of similar design and capacity.   

The three (3) year extended compressor warranty applies only to hermetically and semi-hermetically 

sealed parts of the compressor and does not apply to any other parts or components, including, but not 

limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor starting 

equipment, fan assembly or any other electrical components. 

Horizon Scientific, Inc.’s sole obligation under this warranty is limited to either repair or replacement of 

parts, subject to the additional limitations below.  This warranty neither assumes nor authorizes any 

person to assume obligations other than expressly covered by this warranty. 

NO CONSEQUENTIAL DAMAGES.

  Horizon Scientific, Inc. is not responsible for economic loss; profit loss; 

or special, indirect or consequential damages, including without limitation, losses or damages arising 

from contents spoilage claims whether or not on account of refrigeration failure, electrical failure, 

power failure, or compressor failure.  HORIZON SCIENTIFIC, INC.’S MAXIMUM CUMULATIVE LIABILITY 

RELATIVE TO ALL CLAIMS AND LIABILITIES, INCLUDING OBLIGATIONS UNDER ANY INDEMNITY, WHETHER 

OR NOT INSURED, SHALL NOT EXCEED THE COST OF THE PRODUCT(S) GIVING RISE TO THE CLAIM OR 

LIABILITY.

 

 

 

Содержание ABT-2020MP





















Отзывы: