ABLE BEXS110D Скачать руководство пользователя страница 4

shaped mounting bracket (see figure 1). The angle can then
be adjusted in the direction that the sound is primarily
required to cover. This can be achieved by loosening the two
large bracket screws in the side of the unit, which allow
adjustment in steps of 18

°

. On completion of the installation

the two large bracket adjustment screws on the side of the
unit must be fully tightened to ensure that the unit cannot
move in service.

7)

Safety Warning (Electrostatic Hazard)

The acoustic horn section is made of ABS Plastic, therefore
to avoid a possible ELECTROSTACTIC CHARGE the unit
must only be cleaned with a damp cloth.

8)

Access to the Flameproof Enclosure

In order to connect the electrical supply cables to the sounder
it is necessary to remove the flameproof cover to gain access
to the flameproof chamber. To achieve this remove the four
M6 hexagon socket head screws (see figure 2) and withdraw
the flameproof cover taking extreme care not to damage the
flameproof joints in the process.

Note the four

M6 screws are Class A4-80 stainless steel

and only screws of this category can be used on these
sounders.

It is therefore important that these screws and

their spring washers are kept in a safe place during
installation.

On completion of the cable wiring installation the flameproof
joints should be inspected to ensure that they are clean and
that they have not been damaged during installation. Also
check that the earth bonding wire between the two casting
sections is secure and the ‘O’ ring seal is in place. When

replacing the flameproof cover casting

ensure that it is

square with the flameproof chamber casting before inserting.
Carefully push the cover in place allowing time for the air to
be expelled. Only after the cover is fully in place should the
four M6 Stainless Steel A4-80 cover bolts and their spring
washer be inserted and tightened down. If the cover jams
while it is being inserted, carefully remove it and try again.
Never use the cover bolts to force the cover into position.

9)

Power Supply Selection

It is important that a suitable power supply is used to run the
sounders. The power supply selected must have the
necessary capacity to provide the input current to all of the
sounders connected to the system.

The following table shows the input current taken by the
various sounder units:-

Unit Type

Input

Input

Max.

Voltage

Current

I/P Volts

BExS120D

24V DC

800mA

30V

BExS120D

12V DC

850mA

15V

BExS120D

48V DC

420mA

58V

BExS120D

230V AC

90mA

264V

BExS120D

110V AC

200mA

121V

BExS120D

115V AC

180mA

126V

BExS110D

24V DC

265mA

30V

BExS110D

12V DC

195mA

15V

BExS110D

48V DC

130mA

58V

BExS110D

230V AC

56mA

264V

BExS110D

110V AC

93mA

121V

BExS110D

115V AC

110mA

126V

The input current will vary according to the voltage input level
and the frequency of the tone selected. The current levels
shown above are for the 440Hz Continuous tone @ nominal
input voltage. The 24V and 48V DC units and the 230V AC,
115V AC and 110V AC units have a switching voltage
regulator circuit and therefore the input current level will
decrease slightly as the input voltage in increased and will
increase slightly as the input voltage is reduced. The 12V
units do not have a voltage regulator and therefore their input
current will increase when the input voltage is increased.

The above table also shows the maximum voltages at which
the sounders can be operated.

10)

Cable Selection

When selecting the cable size consideration must be given to
the input current that each unit draws (see table above), the
number of sounders on the line and the length of the cable
runs. The cable size selected must have the necessary
capacity to provide the input current to all of the sounders
connected to the line.

SAFETY WARNING: If the high output BExS120D sounders
are used at high ambient temperatures, i.e. over +40ºC, then
the cable entry temperature may 70ºC and therefore
suitable heat resisting cables must be used, with a rated
service temperature of at least 95ºC.

11)

Earthing

Both AC and DC sounder units must be connected to a good
quality earth. The units are provided with internal and

Figure 1

Plastic Acoustic Horn

Please see Safety Warning
in Section 7 of this manual

Flameproof
Chamber

Flameproof
Cover

S/S Mounting
Bracket

Figure 2

4 off M6 Cover Screws

External Earth
Terminal

Содержание BEXS110D







Отзывы: